Sound Advance FAST MOUNT FM1 Series Скачать руководство пользователя страница 6

Page  6

FM1 

F

AST

M

OUNT

33-4210     05/06

REMOVING THE  LOUDSPEAKER 

1. 

Pull the speaker assembly straight down by the trim bezel 
until the springs become hooked and locked under retaining 
tabs on the mounting hardware (see 

Figure 17

).

2.  Push the loudspeaker assembly upwards until the rim is 

about ¾” below the ceiling surface, then slightly turn the 
speaker assembly clockwise to disengage it from the springs 
(see 

Figure 18

).

3.  Pull the loudspeaker assembly out of the opening and 

remove the input connector from the speaker.

4.  Once disconnected, remove the safety chain or cable (if 

employed) to free the speaker assembly.

IMPORTANT: In order to reinstall the loudspeaker, the 
springs need to be reset in the original “install tabs”, 
otherwise the spring mechanism will not work properly.

SPECIFICATIONS

Radiating Surface: 

8 5 . 5   i n

2

  ( 5 3 2 . 3 c m

2

)   P l a n a r  

   Diaphragm 

Driver System: 

 

0.82 lb (0.37kg) Magnet with 1.02”  

   (26mm) 

voice 

coil

Frequency Response: 

80Hz – 15kHz ±4dB

Power Rating: 

 

20 Watts RMS as per EIA standard  

   RS-426-A

Pressure Sensitivity: 

94dB, 1W/1m

System Impedance:  

8 ohms nominal; 5.5 ohms minimum

Transformer: 

 

Primary Voltage — 70.7 Volts

 

 

 

Primary Taps — 0.5, 1, 2, 4, 8, 16  

   Watts; 

8-ohm 

bypass

Dimensions (Dia x D): 

11¾” x 8¾” (298mm x 222mm)

Cut-Out Diameter: 

10¾” (275mm)

Product Weight:   

6.8 lbs. (3.1kg)

Shipping Weight:   

20.5 lbs (9.3 kg) (box of two)

Packaging:  

 

FM1E — Two (2) to a car ton,

   shipped 

complete 

with 

TBS-FM1 

 

   T-Bar 

Mounting 

Support 

Bridge.

 

 

 

FM1N — Two (2) to a carton,  

   NCB-FM1 

New 

Construction 

 

 

 

 

Bracket shipped separately to  

   facilitate 

pre-installation 

before 

 

   ceiling 

is 

fi 

nished.

If a situation should arise which cannot be resolved through the 
information contained in these pages, please contact SOUND 
ADVANCE Customer Support Services at (800) 592-4644 or 
(949) 492-5449 Monday-Friday, 7 AM to 5 PM Pacifi c Time. 
FAX (949) 361-5151.

Figure 17: Hooking the Mounting Springs in the 

Retaining Tabs

Figure 18: Disengaging the Speaker from the 

Mounting Springs

Содержание FAST MOUNT FM1 Series









Отзывы: