Sony XPERIA Ion LT28at Скачать руководство пользователя страница 57

Страница: 57 / 224

Working Instructions (mech)

1261-4718 Rev 6



Sony Mobile Communications AB

– Company Internal

57(108)

Replacement

4.26 Rubber Mic

Follow the 3.1

– 3.4 Disassembly instructions!

Carry out the Removal as described below.

Prepare a new Rubber Mic.

Carry out the Installation as described below.

Follow the 5.8

– 5.11 Reassembly instructions!

REMOVAL

Detach to remove the gasket Mic on the Frame Rear Cover
as shown in picture by using a Flex Film Assembly Tool.

The gasket Mic must be removed!

If no gasket Mic attached on the Frame Rear Cover, skip
this step!

Detach to remove the Rubber Mic by using a Flex Film
Assembly Tool.

If no Rubber Mic attached on the microphone, skip this
step!

INSTALLATION

Place a new Rubber Mic on the microphone.

Note the orientation of the Rubber Mic to be installed!

Содержание XPERIA Ion LT28at

































































































































































































































Результаты поиска

Содержание XPERIA Ion LT28at

Отзывы:

Похожие инструкции для XPERIA Ion LT28at

Бренды по названию

Популярные бренды

Sony XPERIA Ion LT28at, Руководство по эксплуатации

Результаты поиска

Содержание XPERIA Ion LT28at

Отзывы:

Похожие инструкции для XPERIA Ion LT28at

Бренды по названию

Популярные бренды