manualshive.com logo in svg

Sony XCL-U100, Техническое руководство

Поделиться
Скачать
Sony XCL-U100 Скачать руководство пользователя страница 36

Ca
mer

a

 Cont

rol Comma

nds

Command Specification

36

0: OFF
1: ON

[Parameter 2] <Read beginning column (0 - 1472)>
[Parameter 3] <Read ending column (127 - 1599)>
[Process] Sets the beginning column and ending column 

numbers for reading during horizontal partial scan 
operation.
Set the number of columns to read to a number 
between 128 and 1600.

Note

Depending on the setting for the number of lines or 
number columns to read, images prior to configuration 
may appear in the disabled image display areas. Refer to 
the operating instructions for the interface board, and 
enable compatibility with camera file settings.

IN/OUT Setting Command

x

 External Trigger Signal Input Selection

[Command] EXTTRG
[Parameter 1] <Input specification (0 - 1)>

0: Camera Link

t

DIGITAL IF connector

1: DC

t

DC IN connector

[Process] Selects an input route of the external trigger 

signal.

x

 Grayscale Output Setting

[Command] GRAYSCALE
[Parameter 1] <Mode (0 - 1)>

0: OFF
1: ON

[Process] Sets the grayscale mode.

x

 DC IN Connector Signal Output Setting

[Command] WEN-STRB
[Parameter 1] <Specification for 10th pin output (0 - 2)>

0: GND output
1: DVAL output
2: EXPOSURE output

[Process] Sets the 10th pin of DC IN connector signal 

output specification.

x

 Signal Output Bit Depth

[Command] BIT-DEPTH
[Parameter 1] <Signal Output Bit Depth (0 - 2)>

0: 12 bit output
1: 10 bit output
2: 8 bit output

[Process] Sets the signal output bit depth.

Note

This can also be changed with the IMG-WIZE 
command.

x

 Serial Transmission Speed Setting

[Command] BRATE
[Parameter 1] <Baud rate (0 - 3)>

0: 9600 bps
1: 19200 bps
2: 38400 bps
3: 57600 bps

[Process] Sets the serial transmission speed.

Setting Value Control Command

The setting value control command controls camera 
setting data saved in the EEPROM inside the camera. 
The following list shows the contents.

Setting Initialization Command

x

 Initialization of Setting

[Command] INIT
[Process] Initializes the data corresponding to the 

camera control command to the factory setting value.
However, the settings are not saved (SAVE).

Save Setting Command

x

 Save Setting

[Command] SAVE
[Process] Writes the data corresponding to the camera 

control command in the EEPROM.
Another command is not accepted during execution 
of the process. After completion of execution, the 
following message is displayed.

“OK”: Normal completion

Note

If the completion is not normal, the saved data may be 
damaged. 

Read Setting Command

x

 Read Setting

[Command] LOAD
[Process] Reads the data corresponding to the camera 

control command in the EEPROM. 

Command

Explanation

Initialization 
of setting 
value

Initializes the data corresponding to the 
camera control command to the factory 
setting value.

Save setting

Writes the data corresponding to the camera 
control command in the EEPROM.

Read setting

Reads the data corresponding to the camera 
control command in the EEPROM.

Setting value 
accession

Sends the necessary data to the camera 
control application.

Содержание XCL-U100













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды