manualshive.com logo in svg

Sony Walkman MZ-NF520D, Руководство по обслуживанию

Поделиться
Скачать
Sony Walkman MZ-NF520D Скачать руководство пользователя страница 3

3

MZ-NF520D

CAUTION

Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous ra-
diation exposure.

Notes on chip component replacement

• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-

aged by heat.

Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270 ˚C dur-

ing repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

UNLEADED SOLDER

Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size)

: LEAD FREE MARK

Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 ˚C higher than

ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 ˚C .
Caution: The printed pattern (copper foil) may peel away if the

heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur
such as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

1. SERVICING NOTES

....................................................... 4

2. GENERAL

.......................................................................... 5

3. DISASSEMBLY

3-1. Disassembly Flow .......................................................... 6
3-2. Case (Lower) .................................................................. 7
3-3. MAIN Board ................................................................... 7
3-4. Panel (Upper) Section .................................................... 8
3-5. LCD Module, Button (Control) ..................................... 8
3-6. Mechanism Deck (MT-MZN710-177) .......................... 9
3-7. Set Chassis Assy ............................................................. 9
3-8. OP Service Assy (LCX-5R) ......................................... 10
3-9. Holder Assy .................................................................. 11
3-10. DC Motor (Sled) (M602) ........................................... 11
3-11. DC Motor (Over Write Head Up/Down) (M603),

DC SSM18B Motor (Spindle) (M601) ...................... 12

4. TEST MODE

.................................................................... 13

5. ELECTRICAL ADJUSTMENTS

............................... 18

6. DIAGRAMS

6-1. Block Diagram ............................................................. 37
6-2. Printed Wiring Board - MAIN Board (Side A) ........... 39
6-3. Printed Wiring Board - MAIN Board (Side B) ........... 40
6-4. Schematic Diagram - MAIN Board (1/4) .................... 41
6-5. Schematic Diagram - MAIN Board (2/4) .................... 42
6-6. Schematic Diagram - MAIN Board (3/4) .................... 43
6-7. Schematic Diagram - MAIN Board (4/4) .................... 44
6-8. IC Pin Function Description ........................................ 49

7. EXPLODED VIEWS

7-1. Case Section ................................................................. 55
7-2. Chassis Section ............................................................. 56
7-3. MAIN Board Section ................................................... 57
7-4. Mechanism Deck Section-1 (MT-MZN710-177) ........ 58
7-5. Mechanism Deck Section-2 (MT-MZN710-177) ........ 59

8. ELECTRICAL PARTS LIST

....................................... 60

TABLE OF CONTENTS

Содержание Walkman MZ-NF520D

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды