Sony VPL-FE100U Скачать руководство пользователя страница 4

Страница: 4 / 6

SmartPanel Projector Driver Application Note

Sony VPL-FE100U

[email protected]

II. CONTROL WIRING

PROJECTOR CONTROL

RS232

IR/SERIAL

GND

CTS

RTS

+12V

GND

IR/SER

SENSE

Male DB9

RS-232 to the port labeled

RS-232C/422A

Wired Remote /

Infrared do not

have to be wired

for this projector.

5 4 3 2 1

9 8 7 6

5 4 3 2 1

This section specifies how RS-232 should be wired to the
projector.

RS-232 should be connected to the control port labeled

RS-

232C/422A

. Connection should be as follows:

1. Wire the Panel to a male DB9 as follows:

TX to 2
RX to 3
GND to 5

2. Connect the cable to the projector port labeled

RS-

232C/422A

3. Optionally, an intermediate cable (male DB9 to female

DB9) may be used to facilitate service to the projector
or Panel.

NOTE

Be sure the hardware switch labeled

RS-232C RS-422A

is set to

RS-232C

(to the left) or the projector will not

respond to control properly.

Содержание VPL-FE100U







Результаты поиска

Содержание VPL-FE100U

Отзывы:

Похожие инструкции для VPL-FE100U

Бренды по названию

Популярные бренды

Sony VPL-FE100U, Быстрая справочная инструкция

Результаты поиска

Содержание VPL-FE100U

Отзывы:

Похожие инструкции для VPL-FE100U

Бренды по названию

Популярные бренды