Information in this document is subject to
change without notice.
S
on
y
, VAIO and CLIE are trademarks or regis-
tered trademarks of
S
on
y
. Microsoft, Windows,
Windows Media, Out
l
ook, Bookshe
l
f and other
Microsoft products are trademarks or registered
trademarks of Microsoft Corporation in the
United
S
tates and other countries. The word
B
l
uetooth and the B
l
uetooth
l
ogo are trademarks
of B
l
uetooth
S
IG, Inc. AMD, the AMD
l
ogo, other
AMD product names and combinations thereof
are trademarks of Advanced Micro Devices, Inc.
Inte
l
Inside
l
ogo, Pentium, Ce
l
eron and Core are
trademarks or registered trademarks of Inte
l
Cor-
poration. Transmeta, the Transmeta
l
ogo, Crusoe
Processor, the Crusoe
l
ogo and combinations
thereof are trademarks of Transmeta Corporation
in the U
S
A and other countries. Graffi ti, Hot-
Sy
nc, Pa
l
mModem, and Pa
l
m O
S
are registered
trademarks, and the Hots
y
nc
l
ogo and Pa
l
m are
trademarks of Pa
l
m, Inc. or its subsidiaries. (M)
and Motro
l
a are trademarks of Motrora, Inc. Other
Motro
l
a products and services with (R) mark
l
ike
Dragomba
ll
are the trademarks of Motro
l
a, Inc.
A
ll
other names of s
y
stems, products and services
in this manua
l
are trademarks or registered trade-
marks of their respective owners. In this manua
l
,
the (TM) or (R) mark are not specifi ed.
Caution Markings for Lithium/Ion Batter
y
- The
fo
ll
owing or simi
l
ar texts sha
ll
be provided on
batter
y
pack of equipment or in both the operating
and the service instructions.
CAUTION: Danger of exp
l
osion if batter
y
is
incorrect
ly
rep
l
aced. Rep
l
ace on
ly
with the same
or equiva
l
ent t
y
pe recommended b
y
the manu-
facturer. Discard used batteries according to the
manufacturer’s instructions.
CAUTION: The batter
y
pack used in this device
ma
y
present a fi re or chemica
l
burn hazard if mis-
treated. Do not disassemb
l
e, heat above
60
°C
(
140
°F) or incinerate. Dispose of used batter
y
prompt
ly
. Keep awa
y
from chi
l
dren.
CAUTION: Changing the back up batter
y
.
•
Overcharging, short circuiting, reverse charg-
ing, mu
l
ti
l
ation or incineration of the ce
ll
s must
be avoided to prevent one or more of the fo
l
-
l
owing occurrences; re
l
ease of toxic materia
l
s,
re
l
ease of h
y
drogen and/or ox
y
gen gas, rise in
surface temperature.
•
If a ce
ll
has
l
eaked or vented, it shou
l
d be
rep
l
aced immediate
ly
whi
l
e avoiding to touch
it without an
y
protection.
Ser
v
i
c
e
a
nd Inspe
c
tion Pre
ca
utions
1. Obey pre
ca
ution
a
ry
ma
rkings
a
nd
instru
c
tions
Labe
l
s and stamps on the cabinet, chassis, and
components identif
y
areas requiring specia
l
pre-
cautions. Be sure to observe these precautions,
as we
ll
as a
ll
precautions
l
isted in the operating
manua
l
and other associated documents.
2. Use design
a
ted p
a
rts only
The set’s components possess important safet
y
characteristics, such as noncombustibi
l
it
y
and
the abi
l
it
y
to to
l
erate
l
arge vo
l
tages. Be sure that
rep
l
acement parts possess the same safet
y
charac-
teristics as the origina
l
s. A
l
so remember that the
mark, which appears in circuit diagrams and
parts
l
ists, denotes components that have particu-
l
ar
ly
important safet
y
functions; be extra sure to
use on
ly
the designated components.
3
. Alw
a
ys follow the origin
a
l design
when
m
ounting p
a
rts
a
nd routing
wires
The origina
l l
a
y
out inc
l
udes various safet
y
fea-
tures, such as inc
l
usion of insu
l
ating materia
l
s
(tubes and tape) and the mounting of parts above
the printer board. In addition, interna
l
wiring has
been routed and c
l
amped so as to keep it awa
y
from hot or high-vo
l
tage parts. When mounting
parts or routing wires, therefore, be sure to du-
p
l
icate the origina
l l
a
y
out.
4. Inspe
c
t
a
fter
c
o
m
pleting ser
v
i
c
e
After servicing, inspect to make sure that a
ll
screws, components, and wiring have been
returned to their origina
l
condition. A
l
so check
the area around the repair
l
ocation to ensure that
repair work has caused no damage, and confi rm
safet
y
.
5. When repl
ac
ing
c
hip
c
o
m
ponents...
Never reuse components. A
l
so remember that
the negative side of tanta
l
um capacitors is easi
ly
damaged b
y
heat.
6. When h
a
ndling flexible print
bo
a
rds...
•
The temperature of the so
l
dering-iron tip
shou
l
d be about 270°C.
•
Do not app
ly
the tip more than three times to
the same pattern.
•
Hand
l
e patterns with care; never app
ly
force.
Caution: Remember that hard disk drives are
easi
ly
damaged b
y
vibration. A
l
wa
y
s hand
l
e
with care.
2
[Sony Confidential]
VGN-N
S
Series (9-852-3
9
5-XX)
