Sony TL-HP90, Руководство по обслуживанию

Страница: 3 / 18

3
TL-HP90
Connect the headset
1
Connect the headset plug to the HEADSET jack.
2
Place the earpiece support unit behind the top of your ear.
3
Adjust the length of the headband so that the headset fits on
your ear.
4
The earpiece can be rotated so it fits comfortably over either ear.
5
Position the headset microphone so that it is placed near the mouth.
Notes
•
Listening with headset at high volume may affect your hearing.
• The earpad may deteriorate due to long-term storage or use. If you need to
replacing the earpad, it can be purchase separately (EP-Q1).
Tip
You can use the headset on either your right or left ear.
1 2
3
4
5
Listening to music, etc. from an external equipment
If you want to listen to music, etc. from the external equipment, you can do
it using the headset during TALK off status.
Notes
•
When you are listening to music, etc. with the external equipment connected to
AUDIO IN jack, volume control on the headset is not available. Volume control is
available with the connected equipment.
Also, turning off the sound from the connected equipment can be done either by
shutting down the power for the external equipment or by pulling out the stereo
audio cable from AUDIO IN jack on this unit.
• During conversation, the voice from an external equipment cannot be heard.
• The sound of this unit is a monaural type.
Stereo audio
cable (supplied)
To the headphone jack
(stereo mini-plug)
To AUDIO IN jack
(stereo mini-plug)
e.g.,
cassette player,
radio (not supplied)
Using the headset hunger
The headset can be hung on the hook (supplied) by mounting the handset
hanger (supplied) on the headset.
1
Attach the headset hanger to the headset from the slit as
illustration
A .
Be sure to insert the protrusion of the headset hanger to the
projection of the headset.
2
Hang the headset hanger on the hook.
Note
Do not hang the headset on as illustration B .
2
1
A
B
OFF
RINGER LEVEL
Making and receiving calls
Making a call
1
Press (TALK) .
The lamp lights up.
You hear a dial tone.
2
Dial a phone
number.
3
When you’re done
talking, press
(TALK).
The lamp goes off.
DIAL MODE
switch
(REDIAL/PAUSE)
(* TONE)
(FLASH)
RINGER
LEVEL
switch
(HOLD)
HEADSET
VOLUME
(TEL)
P
DIAL MODE
T
If your dialing system is to Set the switch
Tone T
Pulse P
Lamp
Choose the dialing mode
For the phone to work properly, select an appropriate dialing mode (tone or
pulse).
Depending on your dialing system, set the
DIAL MODE switch as follows:
If you aren’t sure of your dialing system
Make a trial call with the DIAL MODE switch set to T. If the call connects,
leave the switch as is; otherwise, set the switch to P.
Receiving a call
When you hear the phone ring, press
(TALK)
. When you’re done talking,
press
(TALK)
again.
Additional tasks
Do this
Set the RINGER LEVEL switch to H (high), L (low)
or OFF
Turn the HEADSET VOLUME (TEL) up to increase
the receiver volume or down to decrease it.
(continued)
To
Adjust the ringer level
Adjust the receiver volume
Redialing
1
Press (TALK).
The lamp lights up.
2
Press (REDIAL/PAUSE).
Notes
• If the number last dialed exceeds 31 digits for tone dialing or 32 digits for pulse
dialing, the number cannot be dialed.
• The tone and pause are each counted as one digit.
Note
Pressing (HOLD) during dialing may stop transmission of the dial signal, causing you
to dial the wrong phone number.
To
Switch to tone dialing
temporarily
Put a call on hold
Switch to another call
(“call waiting” service*)
Do this
Press
(* TONE)
after you’re connected.
The line will remain in tone dialing until
disconnected.
Press
(HOLD)
. The HOLD button lights up.
Press
(HOLD)
again to resume the conversation.
Press
(FLASH)
.
Press
(FLASH)
again to return to the first caller.
* You need to subscribe to this service with your telephone company.