— 7 —
LED and Fluorescent Indicator Tube All Lit, Key Check Mode (Do not connect the HTC-V5550.)
Procedure:
1.
Press
1/u
button to turn the set ON.
2.
Press the OPEN/CLOSE button to open the sliding panel.
3.
Press three buttons DELAY , ENTER/NEXT , and DISPLAY/DEMO simultaneously.
4.
LEDs and fluorescent indicator tube are all turned on. Each time the MOVIE button is pressed, the fluorescent indicator tube lights up
as follows:
lights up completely
n
lights up partially 1
n
lights up partially 2
n
lights up completely.
5.
Press GAME button, and the key check mode is activated.
6.
In the key check mode, the fluorescent indicator tube displays “K @@ V0 J0”. Each time a button is pressed, “K”value decreases.
However, once a button is pressed, it is no longer taken into account. (@@ means the total of buttons)
“J” Value increases like 1, 2, 3 ... if rotating JOG knob in “+” direction, or it decreases like 0, 9, 8 ... if rotating in “-” direction.
“V” Value increases like 1, 2, 3 ... if rotating VOLUME knob in “+” direction, or it decreases like 0, 9, 8 ... if rotating in “-” direction.
7.
Pressing all buttons lights up the fluorescent indicator tube completely.
8.
To exit from this mode, press three buttons EDIT , ENTER/NEXT and DISPLAY/DEMO simultaneously. (COLD RESET)
9.
To exit from this mode, press three buttons in the same manner as step 1, or disconnect the power cord.
CD, TAPE Deck Aging Mode (This mode can be used only when the HTC-V5550 is connected.)
This mode can be used for checking the operations of the CD player and tape deck.
• When problems occur;
Aging stops, and the stopped state is displayed on the fluorescent indicator tube.
• When no problems;
Aging continues.
Preparations:
• Set the CD on the DISC1 tray.
• Insert a commercially available tape for recording (tapes which contents can be erased, etc.) in decks A and B.
Setting the aging mode:
Press the PLAY MODE button, ENTER/NEXT button, and STEREO/MONO button together.
When the aging mode is set, the CD roulette mark blinks. To exit the mode, press the
1/u
button and turn OFF the power.
Sequence:
The aging mode is executed in the following sequence.
If the function is set to “CD” when the aging mode is set, aging is performed starting from the CD player. When set to “TAPE A” or “TAPE
B”, aging is started from deck A.
If the function is set to others, aging will not be started until the function is switched to CD or TAPE.
Display of status:
• The aging status is displayed on the fluorescent indicator tube.
• Normally, the CD player displays the remaining aging time. But if operations ended abnormally, it displays the cause.
• During the aging of the tape deck, the operations performed will be displayed. If operations ended abnormally, this will be displayed at the
fluorescent display tube.
CD Player
• During normal operations:
Display of fluorescent indicator tube
**1-@@
**: Displays “CD” and the remaining aging time (minutes) alternately. The remaining aging time is counted down from 12.
@@: Track number being accessed.
Aging of CD player (12 minutes)
Aging of deck A
Aging of deck B
12 minutes
Содержание STR-V5550
Страница 22: ...STR V5550 V7770 4 11 SCHEMATIC DIAGRAM SLIDING PANEL SECTION Refer to page 48 for IC Block Diagrams 33 34 ...
Страница 28: ... 44 4 17 SCHEMATIC DIAGRAM AV MIC SECTION STR V5550 V7770 Refer to page 48 for IC Block Diagrams ...
Страница 29: ... 45 4 18 PRINTED WIRING BOARD AV MIC SECTION STR V5550 V7770 Refer to page 10 for Circuit Boards Location ...
