2
STR-DE400
Notes on chip component replacement
•
Never reuse a disconnected chip component.
•
Notice that the minus side of a tantalum capacitor may be
damaged by heat.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•
Unleaded solder melts at a temperature about 40
°
C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°
C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
•
Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE
WITH MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
MODEL IDENTIFICATION
– Rear Panel –
Model
Part No.
AEP, UK models
2-662-058-0
[]
AUS model
2-662-058-1
[]
Taiwan model
2-662-058-2
[]
Korean model
2-662-058-3
[]
Thai model
2-662-058-4
[]
Russian model
2-662-058-5
[]
Parts No.
General
Power requirements
Power consumption
Power consumption (during standby mode)
0.2 W
Dimensions (w/h/d) (Approx.)
430
×
145
×
300 mm
including projecting parts
and controls
Mass (Approx.)
7.8 kg
Design and specifications are subject to
change without notice.
Area code
Power requirements
AEP, UK, RU
230 V AC, 50/60 Hz
AUS
240 V AC, 50 Hz
KR, TH
220 – 230 V AC,
50/60 Hz
TW
110 V AC, 60 Hz
Area code
Power consumption
AEP, UK, AUS,
KR, RU
190 W
TH
170 W
TW
400 W
FM tuner section
Tuning range
87.5 - 108.0 MHz
Intermediate frequency
10.7 MHz
Useable sensitivity
11.2 dBf, 1
µ
V/75 ohms
S/N
Mono/Stereo
76 dB/70 dB
Harmonic distortion at 1 kHz
Mono/Stereo
0.3%/0.5%
Separation
45 dB at 1 kHz
Frequency response 30 Hz – 15 kHz,
+0.5/–2 dB
AM tuner section
Tuning range
Intermediate frequency
450 kHz
Usable sensitivity
50 dB
µ
/m
Video section
Inputs/Outputs
Video:
1 Vp-p/75 ohms
COMPONENT VIDEO:
Y: 1 Vp-p/75 ohms
P
B
/C
B
/B-Y: 0.7 Vp-p/
75 ohms
P
R
/C
R
/R-Y: 0.7 Vp-p/
75 ohms
80 MHz HD Pass Through
Area code
Tuning scale
10 kHz step
9 kHz step
AEP, UK, AUS,
TW, KR, TH, RU
–
531 –
1,602 kHz
About area codes
The area code of the receiver you purchased is
shown on the lower right portion of the rear panel
(see the illustration below).
Any differences in operation, according to the area
code, are clearly indicated in the text, for example,
“Models of area code AA only”.
SURROUND
SPEAKERS
L
R
L
R
+
+
CENTER
FRONT
L
R
L
R
+
+
Area code
• Abbreviation
AUS
: Australian model
KR
: Korean model
RU
: Russian model
TH
: Thai model
TW
: Taiwan model
