Sony StorStation LIB-81 Скачать руководство пользователя страница 36

Страница: 36 / 102

Chapter 3 Basic Usage

Note

The status information can be viewed through a browser. Refer to Chapter 6,
“Library Administration Menu” (page 67).

Menu Items

The following menus are in the control panel.

Information Menu

The AIT library and AIT drive information can be displayed.

The following submenus are in the Information Menu.

• Library Menu

Displays information related to the AIT library.

“Viewing Information Related to the AIT Library” (page 59) in Cha pter 4,

“Operating the AIT Library”.

• Drive Menu

Displays information related to the AIT drives.

“Viewing Information Related to the AIT Drive” (page 62) in Chapter 5,

“Operating the AIT Drive”.

Eject / Insert

System Down

Move Tape

SCSI

Password

Configuration

Network

Tape Inventory

Information

Drive

Library

Information

ENTER

Содержание StorStation LIB-81







































































































Результаты поиска

Содержание StorStation LIB-81

Отзывы:

Похожие инструкции для StorStation LIB-81

Бренды по названию

Популярные бренды

Sony StorStation LIB-81, Руководство по эксплуатации

Результаты поиска

Содержание StorStation LIB-81

Отзывы:

Похожие инструкции для StorStation LIB-81

Бренды по названию

Популярные бренды