Sony SPP-SS955 - Cordless Telephone, Руководство по обслуживанию

Страница: 16 / 48

– 16 –
5-2. HANDSET
[Start-up]
1. With the power supplied, press
[TALK]
,
[0]
, and
[1]
keys simul-
taneously, and the Test Mode will start.
2. Allow for normal ringer to sound at high level for duration of
500 msec after start-up, then the handset will go in Test Mode
Idle status.
3. The RF in Talk/Intercom status is as follows.
TALK LED lights up.
[Test Mode by Manual Input]
• The key input in the Test Mode Idle status can change the set
status to the following modes. However, the transition to an-
other mode within respective test mode groups (A-J) is possible
directly, but in case of transition to other test mode group, the
set must be returned to the Test Mode Idle status once by enter-
ing the command “0-1-#”.
A) Test mode termination
Command Mode/Operation
0-0-# The Test mode terminates. The contents of EEPROM
are cleared. In case of successful clear, an
acknowledge tone sounds.
B) Return test mode idle
Command Mode/Operation
0-1-# Return to Test Mode Idle status.
C) Continuous receiving test group (Note 1)
Command Mode/Operation
1-1-# CH1 continuous receiving status (LNA, AGC ON)
D) Continuous transmission test group (Note 1)
Command Description
2-1-# CH1 continuous transmission status (TX Power High)
2-2-# CH1 continuous transmission status (TX Power Mid)
2-3-# CH1 continuous transmission status (TX Power Low)
Note 1: Each time the
[*]
key is pressed, the channels change over as
follows:
CH1
→
CH2
→
CH3
→ … →
CH20
E) Loopback test group 1
Command Mode/Operation
3-1-# CODEC Forward Loopback (L1)
(MIC
→
SP) (within CODEC)
3-2-# ADPCM Forward Loopback (L2)
(MIC
→
CODEC
→
ADPCM
→
CODEC
→
SP)
3-3-# ADPCM
→
RF Loopback
(MIC
→
CODEC
→
ADPCM
→
RF
→
ADPCM
→
CODEC
→
SP)
F) TDD test group 1
Command Mode/Operation
4-1-# CH1 TDD mode (Master timing, Power High) status
4-2-# CH1 TDD mode (Master timing, Power Mid) status
4-3-# CH1 TDD mode (Master timing, Power Low) status
4-4-# TDD mode (Slave timing, Standby) status. Power
control
G) MMI test group
Command Mode/Operation
5-1-# Key test.
• Press the keys successively in the following
order:
[TALK/FLASH]
→
[OFF]
→
[HOLD]
→
[PGM]
→
[INTERCOM]
→
[REDIAL/PAUSE]
→
[1]
→
[2]
→
[3]
→
[4]
→
[5]
→
[6]
→
[7]
→
[8]
→
[9]
→
[*]
→
[0]
→
[#]
→
[SPEED DIAL]
• If key input sequence is correct: An acknowl-
edge tone sounds, and the set returns to the Test
Mode Idle status.
• If key input sequence is wrong: An error tone
sounds, and the set returns to the Test Mode
Idle status.
H) TDD test group 2
Command Mode/Operation
6-1-# TDD mode (Master timing) status.
I) Memory clear test group
Command Mode/Operation
7-1-# The contents of EEPROM are cleared. In case of
successful clear, an acknowledge tone sounds.
J) Battery save mode
Command Mode/Operation
9-0-# Battery Save mode.
www. xiaoyu163. com
QQ 376315150
9 9
2
8 9
4 2
9 8
TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com