background image

2

US

Caution

You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate this
equipment.
Privacy of communications may not be ensured
when using this phone.

Note

This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the

equipment and receiver.

– Connect the equipment into an outlet on a

circuit different from that to which the
receiver is connected.

– Consult the dealer or an experienced radio/

TV technician for help.

Operation is subject to the following two
conditions: (1)This device may not cause
interference, and (2)This device must accept any
interference, including interference that may
cause undesired operation.

IMPORTANT NOTE

To comply with FCC RF exposure compliance
requirements, please follow the following
guidelines in order to protect body from
exposing to RF electromagnetic energy.
1. Avoid direct body contact with transmitting

antenna during telephone conversation.

2. Do not replace or modify the transmitting

antenna in any way.

IMPORTANT
SAFETY
INSTRUCTIONS

When using your telephone
equipment, basic safety precautions
should always be followed to reduce
the risk of fire, electric shock and
injury to persons, including the
following:
1. Do not use this product near

water, for example, near a bath
tub, wash bowl, kitchen sink, or
laundry tub, in a wet basement, or
near a swimming pool.

2. Avoid using a telephone (other

than a cordless type) during an
electrical storm.  There may be a
remote risk of electric shock from
lightning.

3. Do not use the telephone to report

a gas leak in the vicinity of the
leak.

4. Use only the power cord and

batteries indicated in this manual.
Do not dispose of batteries in a
fire. They may explode. Check
with local codes for possible
special disposal instructions.

SAVE THESE
INSTRUCTIONS

Owner’s Record

The model and the serial numbers are
located at the bottom of the unit.  Record
the serial number in the space provided
below.  Refer to these numbers
whenever you call upon your Sony
dealer regarding this product.
Model No. SPP-S2720
Serial No.   ________________

Содержание SPP-S2720









































































Отзывы: