Sony SDZ-S100 Скачать руководство пользователя | Manualshive

Страница: 27 / 64

background image

27

Chapter 2 Installation

Connecting the SCSI Bus Cable (SDZ-S100 only)

Connect the SDZ-S100 (SCSI model) and the host computer with a SCSI cable.
This section describes how to do so. Use an Ultra 160/m SCSI LVD cable
commonly sold in stores to connect the unit to the SCSI bus. The SDZ-S100
uses a 68-pin half pitch connector.

Caution

• Do not connect the SDZ-S100 to a HVD (High Voltage Differential) SCSI

bus. If you do, the unit or other devices on the SCSI bus may be damaged.

• Turn off all the connected devices before connecting the SCSI cable,

including the SDZ-S100 and the host computer.

• If the SDZ-S100 is the last or only device on the SCSI bus, make sure that you

connect the terminator to the open connector.

• Make sure that the SCSI connectors are securely connected.
• With LVD (Low Voltage Differential) SCSI, make the total length of the

SCSI cable (internal and external) connecting the host computer and the
device at the end of the SCSI bus shorter than 12 m (39.4 ft.). On an LVD bus
with a single device, make this length shorter than 25 m (82 ft.). The SDZ-
S100 internal cable length is 25 cm (9.8 in.).

• SCSI cables cannot be branched.

1

Make sure that the host computer and the SDZ-S100 are off.

2

Connect the SCSI cable and terminator as shown below.

The SCSI cable can be up to 24.7 m (81 ft.) long. (The SDZ-S100 internal
cable length is 25 cm (9.8 in.).)

A SCSI bus allows you to connect up to fifteen peripherals to the host computer,
including the unit.

Host computer

SCSI connector

SCSI cable

Terminator

«
...
25
26
27
28
29
...
»

Содержание SDZ-S100

































































Отзывы:

Нет отзывов

Похожие инструкции для SDZ-S100

RACK PRO MINI-SAS

Бренд: OWC Страницы: 12

Бренд: ABB Страницы: 2

Бренд: Geekworm Страницы: 13

EonStor DS B Series

Бренд: Infotrend Страницы: 157

Бренд: Johnson Controls Страницы: 2

Бренд: HP Страницы: 18

StorageWorks 2500

Бренд: HP Страницы: 91

StorageWorks RDX

Бренд: HP Страницы: 12

StorageWorks 2012i

Бренд: HP Страницы: 86

StorageWorks SB40c

Бренд: HP Страницы: 36

StorageWorks X5000

Бренд: HP Страницы: 39

StorageWorks SB40c

Бренд: HP Страницы: 10

Бренд: HP Страницы: 252

StorageWorks 600 - Modular Disk System

Бренд: HP Страницы: 63

StorageWorks 2000 Series

Бренд: HP Страницы: 330

StorageWorks 300

Бренд: HP Страницы: 180

Бренд: ClearSpan Страницы: 25

Бренд: OLT Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды