Sony SCD-1/777ES Скачать руководство пользователя страница 13

Страница: 13 / 78

6. Press the

button.

7. Check that the waveform on oscilloscope is clear, and the level

and jitter of waveform satisfy the specifications.

8. After checking, press the

button.

9. Repeat steps 3 through 8 for respective discs.
10. Press the

button to turn the power off.

Specified Value:

Disc

Jitter (displayed value)

SATD-S2

1.25 to 1.65 Vp-p

20 (Hex) or less

TCD-784

1.3 to 1.7 Vp-p

15 (Hex) or less

bbb

CD1

Discchk

Disc type (refer to Disc check list (page 11))

6. Press the

button and

button, the

button and

but-

ton, and the

button and

button on the remote commander

successively to execute the focus search.

7. Check that the waveform on oscilloscope is within the level

and

specifications.

8. After checking, press the

button.

9. Repeat steps 3 through 8 for respective discs.
10. Press the

button to turn the power off.

Specified Value:

Disc

SATD-S2

1.5 to 2.3Vp-p

- 0.1 to +0.1V

TCD-784

S Curve Check

Connection:

RF Level Check

Connection:

MAIN board

TP524 (FE)

TP501 (VC)

+
–

oscilloscope

(normal mode)

Procedure:
1. Connect an oscilloscope to the TP524(FE) and TP501(VC) on

the MAIN board.

2. Set the Adjustment-1 Mode. (See 5-2. Adjustment-1 Mode in

SECTION 5 (page 11))

3. Set a disc (SATD-S2 or TCD-784).
4. Press the

button and

button on the remote commander

to make the disc type checked.

Note:

If the disc check was made in the Adjustment-1 Mode, pressing
another button immediately after pressing the

and

buttons

on the remote commander could cause the microcomputer to run
out of control, thus requiring extreme care.

5. Confirm that the disc was checked.

S curve waveform

MAIN board

TP503 (RF)

TP501 (VC)

+
–

oscilloscope
(auto mode)

Procedure:
1. Connect an oscilloscope to the TP503(RF) and TP501(VC) on

the MAIN board.

2. Set the Adjustment-1 Mode. (See 5-2. Adjustment-1 Mode in

SECTION 5 (page 11))

3. Set a disc (SATD-S2 or TCD-784).
4. Press the

button and

button on the remote commander

to make the disc type checked.

Note:

If the disc check was made in the Adjustment-1 Mode, pressing
another button immediately after pressing the

and

buttons

on the remote commander could cause the microcomputer to run
out of control, thus requiring extreme care.

5. Confirm that the disc was checked.

VOLT/DIV: 200 mV
TIME/DIV: 500 ns

RF signal waveform

bbb

CD1

+ 00

~00

Jitter value
(HEX)

not fixed

Adjustment Location : See page16.

bbb

CD1

Discchk

Disc type (refer to Disc check list (page 11))

Note:

For easier observation of this waveform, extend the sweep time

and raise the brightness.

Note:

Clear RF waveform refers to the waveform where

◊

shapes should

be distinctively observed in the center.

Display example:

Содержание SCD-1/777ES















































































Результаты поиска

Содержание SCD-1/777ES

Отзывы:

Похожие инструкции для SCD-1/777ES

Бренды по названию

Популярные бренды

Sony SCD-1/777ES, Руководство по обслуживанию

Результаты поиска

Содержание SCD-1/777ES

Отзывы:

Похожие инструкции для SCD-1/777ES

Бренды по названию

Популярные бренды