HCD-F200/F500
52
• IC Pin Function Description
MAIN BOARD IC101 R5F3640DDFAR (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Description
1
SYS_RXD
O
Serial data output to the SYSTEM CONTROL connector (SA-WSF200/F500)
2
SYS_CLK
O
Serial data transfer clock signal output to the SYSTEM CONTROL connector
(SA-WSF200/F500)
3
CEC_RX_IN
I
CEC serial data input from the HDMI OUT connector
4
SIRCS_IN
I
SIRCS signal input from the remote control receiver
5
CODEC_DO
O
Serial data output to the A/D, D/A converter
6
CODEC_DI
I
Serial data input from the A/D, D/A converter
7
CODEC_CLK
O
Serial data transfer clock signal output to the A/D converter, D/A converter
8
BYTE
I
External data bus width selection signal input terminal Fixed at "L" in this set
9
CNVSS
I
Processor mode switch input terminal
10
CODEC_PDN
O
Reset signal output to the A/D, D/A converter "L": reset
11
CODEC_CS
O
Chip select signal output to the A/D, D/A converter
12
RESET
I
System reset signal input from the SYSTEM CONTROL connector (SA-WSF200/F500)
"L": reset
For several hundreds msec. after the power supply rises, "L" is input, then it change to "H"
13
XOUT
O
Main system clock output terminal (10 MHz)
14
VSS
-
Ground terminal
15
XIN
I
Main system clock input terminal (10 MHz)
16
VCC1
-
Power supply terminal (+3.3V)
17
NMI
I
Non-maskable interrupt input terminal Fixed at "H" in this set
18
CODEC_INT
I
Interrupt signal input from the A/D, D/A converter
19, 20
-
-
Not used
21
DOUT_MUTE
O
Digital signal on/off control signal output terminal (F200)
22
CEC_TX_OUT
O
CEC serial data output to the HDMI OUT connector
23
VIDEO_MUTE 0
O
Video signal input selection signal output terminal
24
-
-
Not used
25
V_SEL
O
Video signal input selection signal output terminal
26
BACKLIGHT_LED
O
LED drive signal output terminal
27
DMPORT_DET
I
Connect detection signal input from the DMPORT jack
28
VIDEO_MUTE1
O
Video signal input selection signal output terminal
29
I2C_CLK
I/O
Two-way I2C clock bus terminal Not used
30
I2C_DATA
I/O
Two-way I2C data bus terminal Not used
31
DMPORT_TX_OUT
O
Serial data output to the DMPORT connector
32
DMPORT_RX_IN
I
Serial data input from the DMPORT connector
33
CLK1
-
Not used
34
RTS1
-
Not used
35
DVD_SID
O
Serial data output to the servo DSP
36
DVD_SOD
I
Serial data input from the servo DSP
37
DVD_SCO
I
Serial data transfer clock signal input from the servo DSP
38
SYS_WAKEUP
O
System wake up signal output to the SYSTEM CONTROL connector (SA-WSF200/F500)
39, 40
-
-
Not used
41
EPM
-
Not used
42
-
-
Not used
43
P_CONT_HDMI
O
HDMI control signal output terminal (F500)
44
P_CONT1
O
Power on/off control signal output terminal "H": power on
45
-
-
Not used
46
FLASH_CE
-
Not used
47
P_CONT_FL
O
Power on/off control signal output terminal for the front panel section "H": power on
48 to 55
-
-
Not used
56
LED_1
O
LED drive signal output terminal
57
LED_2
O
LED drive signal output terminal
58
LED_3
O
LED drive signal output terminal Not used
59
STBY_LED
O
LED drive signal output terminal Not used
60, 61
-
-
Not used
