background image

2

SA-VE155/WMS155/SS-MS155

SAFETY-RELATED  COMPONENT  WARNING!!

COMPONENTS  IDENTIFIED  BY  MARK  

0

  OR  DOTTED  LINE

WITH  MARK  

0

  ON  THE  SCHEMATIC  DIAGRAMS  AND  IN

THE  PARTS  LIST  ARE  CRITICAL  TO  SAFE  OPERATION.
REPLACE  THESE  COMPONENTS  WITH  SONY  PARTS  WHOSE
PART  NUMBERS  APPEAR  AS  SHOWN  IN  THIS  MANUAL  OR
IN  SUPPLEMENTS  PUBLISHED  BY  SONY.

 UNLEADED SOLDER

Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)

 : LEAD FREE MARK

Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40

°

C higher than

ordinary solder.

Ordinary soldering irons can be used but the iron tip has to be

applied to the solder joint for a slightly longer time.

Soldering irons using a temperature regulator should be set to

about 350

°

C.

Caution: The printed pattern (copper foil) may peel away if

the heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow)

than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may

also be added to ordinary solder.

TABLE OF CONTENTS

1. GENERAL

Location of Controls ................................................................ 3

2. DIAGRAMS

2-1.   Note for Printed Wiring Boards and
         Schematic Diagrams ............................................................ 3
2-2.   Circuit Boards Location ...................................................... 3
2-3.   Printed Wiring Boards (SA-WMS155) ............................... 4
2-4.   Schematic Diagram (SA-WMS155) ................................... 5
2-5.   IC Block Diagram ............................................................... 6

3. EXPLODED VIEWS

.......................................................... 7

4. ELECTRICAL PARTS LIST

........................................... 8

Содержание SA-VE155











Отзывы: