Sony RM-PJVW10, Руководство по обслуживанию

Страница: 24 / 118

1-18
VPL-VW10HT
34
(GB)
Maintenance
Replacing the Lamp
When the lamp becomes darker, replace the lamp
promptly with a new LMP-P200 Projector Lamp (not
supplied).
It is recommended to replace the lamp with a new one
after about 1000 hours for the OFF setting, or about
2000 hours for the ON setting in the CINEMA
BLACK.
When replacing the lamp after using the
projector
Turn off the projector, then unplug the power cord.
Wait for at least an hour for the lamp to cool.
Note
The lamp becomes a high temperature after turning
off the projector with the
I
/
1
key. If you touch the
lamp, you may scald your finger. When you replace
the lamp, wait for at least an hour for the lamp to cool.
1
Place a protective sheet (cloth) beneath the
projector.
Hold the projector and turn the projector toward
the back as shown below.
Note
When replacing the lamp, be sure the unit is on a
flat and stable surface.
2
Open the lamp cover by loosening one screw with
the Philips screwdriver (supplied with the LMP-
P200 Projector Lamp).
3
Loosen two screws on the lamp unit with the
Philips screwdriver.
4
While holding the handle and keeping the lamp
unit horizontal, pull straight up.
Notes
• Pull out the lamp unit by holding the handle. If
you touch the lamp unit, you may be burned or
injured.
• When removing the lamp unit, make sure it
remains horizontal, then pull straight up. Do not
tilt the lamp unit. If you pull out the lamp unit
while tilted and if the lamp breaks, the pieces
may scatter, causing injury.
• If the lamp breaks, consult with qualified Sony
personnel.
5
Insert the new lamp all the way in until it is
securely in place. Tighten the screws. Fold down
the handle.
Notes
• Be careful not to touch the glass surface of the
lamp.
• The power will not turn on if the lamp is not
secured properly.
Maintenance
35
(GB)
Maintenance
6
Close the lamp cover and tighten the screw.
7
Turn the projector back over.
8
Connect the power cord and turn the projector to
the standby mode.
9
Press the following keys on the control panel in
the following order for less than in five seconds
each: RESET,
< , , , ENTER.
Notes
• Do not put your hands into the lamp replacement
spot, or not fall any liquid or object into it to avoid
electrical shock or fire.
• Be sure to use the LMP-P200 Projector Lamp for
replacement. If you use lamps other than LMP-P200,
the projector may cause a malfunction.
• Be sure to turn off the projector and unplug the
power cord before replacing the lamp.
Disposal of used projector lamp
As the materials used in this lamp are similar to those
of a fluorescent lamp, you should dispose of a used
projector lamp in the same way as a fluorescent lamp.
Cleaning the Air Filter
The air filter should be cleaned every 300 hours.
When it becomes difficult to remove the dust from the
filter, replace the filter with a new one.
To clean the air filter, follow the steps below:
1
Turn off the power and unplug the power cord.
2
While pressing the triangle mark on the air filter
cover, slide and remove the air filter cover (at the
bottom of the projector).
3
Pull up the spring.
4
Remove the air filter.
5
Remove the dust from the filter with a vacuum
cleaner.
6
Attach the air filter and replace the cover.
Notes
• If the air filter is excessively dirty, wash it with a
mild detergent solution and dry it in a shaded place.
If the dust cannot be removed, replace the air filter
with the supplied new one.
• Be sure to attach the air filter cover firmly; the power
will not be turned on if it is not closed securely.
Maintenance