![Sony PS3 INFIMOD Скачать руководство пользователя страница 42](http://html.mh-extra.com/html/sony/ps3-infimod/ps3-infimod_installation-manual_406351042.webp)
2. Choose Mode 0.
3. Choose Quick Scope.
4. Push and hold
X
button.
5. After 4 seconds the
4th LED
will blink.
6. Count the required number of blinks for your weapon and release
X
button when it blinked
required number. For example if your weapon MW2-Barret.50CAL then count 14 blinks
and immediately release
X
button.
7. Tap
L1
button to check your setting with your weapon.
MW2-Barret.50CAL - 14
MW2-Intervention - 15
MW2-WA2000 - 14
MW2-M21EBR - 13
MW2-FAL - 8
MW2/SHP*-Barret.50CAL - 10
MW2/SHP*-Intervention - 9
MW2/SHP*-WA2000 - 8
MW2/SHP*-M21EBR - 8
MW2/SHP*-FAL - 5
BlackOps-WA2000 - 11
BlackOps-Dragunov - 13
BlackOps-L96A1 - 14
BlackOps-PSG1 - 14
BlackOps-M14 - 6
BlackOps-FNFAL - 6
BlackOps/SHP*-M14 - 5
BlackOps/SHP*-FNFAL - 5
MW3-Barret.50CAL - 14
MW3-L118A - 14
MW3-ASSO - 14
MW3-RSASS - 14
MW3-Dragunov - 15
MW3-MSR - 16
MW3-MK14 - 10
MW3/QP*-Barret.50CAL - 9
MW3/QP*-L118A - 10
MW3/QP*-ASSO - 10
MW3/QP*-RSASS - 10
MW3/QP*-Dragunov - 9
MW3/QP*-MSR - 11
MW3/QP*-MK14 - 5
*SHP - Sleight of Hand Pro
*QP - Quickdraw Pro
Содержание PS3 INFIMOD
