41
Basic Operations of the Function Menu
Chapt
er
3
Pre
para
tio
ns
P3 AUDIO page
a) To enable this setting, the following settings are also required, in the same
way as for volume operations for channels 1 to 4.
• Set the VARIABLE switch of the front panel to “REC” or “PB”.
• Set setup menu item 131 AUDIO VOLUME to “each”.
P4 TC page
P5 OTHER page
Item
Setting
F1: A5 VOL
Sets the volume of audio channel 5.
a)
The volume can be adjusted within the
range from
–200 to 0 to +200
(–
∞
to
+12 dB)
by turning the PUSH SET knob.
The volume changes in steps of ±10 if you
hold the SHIFT button down while you turn
the knob.
F2: A6 VOL
Sets the volume of audio channel 6.
a)
The volume can be adjusted within the
range from
–200 to 0 to +200
(–
∞
to
+12 dB)
by turning the PUSH SET knob.
The volume changes in steps of ±10 if you
hold the SHIFT button down while you turn
the knob.
F3: A7 VOL
Sets the volume of audio channel 7.
a)
The volume can be adjusted within the
range from
–200 to 0 to +200 (–
∞
to
+12 dB)
by turning the PUSH SET knob.
The volume changes in steps of ±10 if you
hold the SHIFT button down while you turn
the knob.
F4: A8 VOL
Sets the volume of audio channel 8.
a)
The volume can be adjusted within the
range from
–200 to 0 to +200 (–
∞
to
+12 dB)
by turning the PUSH SET knob.
The volume changes in steps of ±10 if you
hold the SHIFT button down while you turn
the knob.
F5: AU METER Selects the display mode of the audio level
meters.
FULL:
Display the range from –60 dB to 0
dB.
FINE:
Display a magnified section with
0.25 dB step marks.
F6: LEVEL MT
Specifies the position at which to
superimpose audio level meters in the
video monitor screen (in full-screen display
mode).
OFF:
Do not superimpose.
LEFT:
Superimpose the audio level
meters of 2 channels on the left side.
RIGHT:
Superimpose the audio level
meters of 2 channels on the right side.
LEFT(4):
Superimpose the audio level
meters of 4 channels on the left side.
RIGHT(4):
Superimpose the audio level
meters of 4 channels on the right side.
LEFT(8):
Superimpose the audio level
meters of 8 channels on the left side.
RIGHT(8):
Superimpose the audio level
meters of 8 channels on the right side.
Item
Setting
F1: TCG
Selects the timecode signal to which the
internal timecode generator synchronizes.
INT:
Follow the initial value set from the
front panel or remotely from the
device connected to the REMOTE
(9P) connector.
EXT:
Synchronize to external timecode
signal input to the TIME CODE IN
connector.
SDI:
Synchronize to timecode embedded
in the HDSDI or SDSDI signal input to
the SD/HDSDI INPUT connector.
F2: PRST/RGN Selects the following for the internal
timecode generator.
PRESET:
Presets an initial value for the
timecode generated by the internal
timecode generator, as specified from
the front panel or remotely from the
device connected to the REMOTE
(9P) connector.
TC:
Generate timecode synchronized to
timecode read by the internal
timecode reader.
VITC:
Generate timecode synchronized to
VITC read by the internal timecode
reader.
F3: RUN
MODE
Selects the timecode run mode.
FREE RUN:
Timecode advances as long
as the unit is powered on, regardless
of the unit’s operating state.
REC RUN:
Timecode advances only
during recording. When you select this
item, also set F1: TCG on this page to
“INT” and set F2: PRST/RGN to
“PRESET”.
F4: DF/NDF
Selects the frame count mode for the
internal timecode generator and the
counter in 59.94i/59.94P/29.97P mode.
DF:
Drop-frame mode
NDF:
Non-drop-frame mode
F5: PDPSET
When the system frequency is set to 1080/
59.94i, 1080/29.97P, or 720/59.94P,
presets the timecode of the A frame of the
pulldown sequence.
24F TC:
Reference timecode for A frame
30F TC:
Timecode after pulldown
conversion from 24-frame timecode
F6: TCR
Selects the type of timecode to display in
the time data display area.
TC:
Display TC.
VITC:
Display VITC.
Item
Setting
F1: INDEX
Sets the index picture (thumbnail) of a clip
being played back
F2: ERR LOG
Displays the error log screen.
F3: CREATE
NEW EDL
Creates a new EDL
