68
File Operations in File Access Mode (for Windows)
Chapt
er 5 F
ile Ope
rat
ions
1
If there is a disc loaded in this unit, put the unit into the
following state.
• Recording, playback, search and other disc
operations: Stopped
• THUMBNAIL button
• Disc access by DELETE LAST CLIP, DELETE
ALL CLIPS, QUICK FORMAT in the DISC menu,
and so on: Stopped
• MENU button: OFF
• Unsaved current clip list: Save or clear
2
Connect the S400 connector on this unit to the
i.LINK (IEEE1394) connector on the remote
computer, using an i.LINK cable.
Windows recognizes this unit as a removable disc, and
displays one of the following icons on the remote
computer’s task bar:
• Windows XP:
• Windows Vista:
The remote computer is now able to perform file
operations when a disc is inserted into this unit.
When you make your first FAM connection
The Found New Hardware Wizard dialog appears when
you connect this unit to your computer. Select “Install the
software automatically (Recommended)”, and then click
the Next button. Click the Finish button when the software
installation finishes.
Operation limitations during FAM connections
• With the exception of the EJECT button, recording
buttons and playback control buttons are disabled.
• This unit cannot be controlled from any device
connected to an external device connector.
• There is no signal output from this unit, and the message
“PC REMOTE!” appears in the display of this unit and
on the external monitor.
Operating on Files
Proceed as follows.
1
Start Explorer.
Check that a drive letter has been assigned to this unit.
(The drive letter will differ depending on the number
of other peripherals connected to the remote
computer.)
2
Use Explorer to perform file operations on the disc
loaded in this unit.
You can operate in the same way that you operate on
local drives and files on network computers.
• If you power this unit off during an FAM
connection, the data transferred thus far is discarded.
• All file operations are not possible for some types of
files.
To eject discs from a remote computer
Right click the icon representing this unit in Explorer, and
select “Eject” from the menu which appears.
To exit file operations
Proceed as follows.
Do not disconnect the cable before performing steps
1
to
3
.
1
Do one of the following on the
or
icon
displayed in the remote computer’s taskbar.
• Double click.
• Right click, and select “Safely Remove Hardware”
from the menu which appears.
Safety Remove Hardware dialog box appears.
2
Select “Sony XDCAM PDW-75MD IEEE 1394 SBP2
Device” and click “Stop”.
The “Stop a Hardware device” dialog appears.
3
Select “Sony XDCAM PDW-75MD IEEE 1394 SBP2
Device” and click “OK”.
In Windows XP, “Sony XDCAM PDW-75MD IEEE
1394 SBP2 Device” is deleted from the list of
“hardware devices”.
In Windows Vista, the message “This device can be
safely removed from your computer.” appears.
This unit can now resume normal operations. (The
limitations described in
no longer apply.)
4
Disconnect the i.LINK cable as required.
PHONES
VCR
JOG
MARK1
MENU
PAGE DISPLAY
CLIP
F1
F5
F4
F3
F2
SHIFT
CLIP
MENU
ESSENCE
MARK
EDIT
SET
THUMB
NAIL
RESET
OUT
IN
MARK2
SHUTTLE
TOP
F REV
F FWD
END
PREV
NEXT
PLAY
STOP
REC
CH-1
2 CH
3 CH
4 CH
NETWORK
LOCAL
REMOTE
ACCESS
LEVEL
REC
VARIABLE
PRESET
PB
File data
Transfer of files
Disc recorder (this unit)
Laptop computer, etc.
i.LINK cable (not supplied)
Notes
Note
Содержание PDW-75MD
Страница 103: ...Sony Corporation ...
