– 16 –
5-8.
FOCUS BIAS ADJUSTMENT
Adjusting Method:
1. Load a continuously recorded disc (Refer to “5-4. Creating
MO Continuously Recorded Disc”.).
2. Press the
=
0
button or
)
+
button and display
“CPLAY MODE”.
3. Press the YES button and display “CPLAY MID”.
4. Press the EDIT/NO button when “C1=
AD= ” is dis-
played.
5. Press the
=
0
button or
)
+
button and display
“FBIAS ADJUST”.
6. Press the YES button and display “
/
a= ”.
The first four digits indicate the C1 error rate, the two digits
after [/] indicate ADER, and the 2 digits after [a=] indicate the
focus bias value.
7. Press the
)
+
button and find the focus bias value at
which the C1 error rate becomes 220. (Refer to note 2.)
8. Press the YES button and display “
/
b=
”.
9. Press the
=
0
button and find the focus bias value at
which the C1 error rate becomes 220. (Refer to note 2.)
10. Press the YES button and display “
/
c=
”.
11. Check that the C1 error rate is below 50 and ADER is 00.
Then press the YES button.
12. If the “(
)” in “
-
-
( )” is above 20, press the YES
button.
If below 20, press the EDIT/NO button and repeat the ad-
justment from step 2 again.
13. Press the EDIT/NO button and press the
6
button to re-
move the continuously recorded disc.
Note 1: The relation between the C1 error and focus bias is as
shown in the following figure. Find points a and b in the
following figure using the above adjustment. The focal
point position c is automatically calculated from points a
and b.
Note 2: As the C1 error rate changes, perform the adjustment us-
ing the average vale.
5-9.
ERROR RATE CHECK
5-9-1.
CD Error Rate Check
Checking Method:
1. Load a test disc TDYS-1.
2. Press the
=
0
button or
)
+
button and display
“CPLAY MODE”.
3. Press the YES button and display “CPLAY MID”.
4. “C1=
AD=
” is displayed.
5. Check that the C1 error is below 20.
6. Press the EDIT/NO button, stop playback, press the
6
but-
ton, and remove the test disc.
5-9-2.
MO Error Rate Check
Checking Method:
1. Load a continuously recorded disc (Refer to “5-4. Creating
MO Continuously Recorded Disc”.).
2. Press the
=
0
button or
)
+
button and display
“CPLAY MODE”.
3. Press the YES button and display “CPLAY MID”.
4. “C1=
AD=
” is displayed.
5. If the C1 error is below 50, check that ADER is 00.
6. Press the EDIT/NO button, stop playback, press
the
6
button, and remove the continuously recorded disc.
5-10. FOCUS BIAS CHECK
Change the focus bias and check the focus tolerance amount.
Checking Method:
1. Load a continuously recorded disc (Refer to “5-4. Creating
MO Continuously Recorded Disc”.).
2. Press the
=
0
button or
)
+
button and display
“CPLAY MODE”.
3. Press the YES button and display “CPLAY MID”.
4. Press the EDIT/NO button when “C1=
AD=
” is dis-
played.
5. Press the
=
0
button or
)
+
button and display
“FBIAS CHECK”.
6. Press the YES button and display “
/
c=
”.
The first four digits indicate the C1 error rate, the two digits
after [/] indicate ADER, and the 2 digits after [c=] indicate the
focus bias value.
Check that the C1 error is below 50 and ADER is 00.
7. Press the YES button and display “
/
b=
”.
Check that the C1 error is not below 220 and ADER is not
above 00 every time.
8. Press the YES button and display “
/
a=
”.
Check that the C1 error is not below 220 and ADER is not
above 00 every time.
9. Press the EDIT/NO button, next press the
6
button, and re-
move the continuously recorded disc.
Note 1: If the C1 error and ADER are above 00 at points a or b,
the focus bias adjustment may not have been carried out
properly. Adjust perform the beginning again.
C1 error
220
a
Focus bias value
(F. BIAS)
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
