English
Before operating the unit, be sure read this manual thoroughly, and
retain it for future reference.
Overview
The LKRA-005 3D lens filter is a 3D shooting kit for use in combination
with a 3D projection lens unit for the SRX-R320S Digital Cinema Projector.
Consult your Sony representative about other combinations.
Attaching 3D Lens Filters
For customers
The task of attaching the 3D lens filters carry risk of fire and for personal
injury.
Users should request that Sony personnel attach the 3D lens filters.
For Sony representative
Refer to the Service Manual (not supplied) of the LKRA-005 for the
procedure for attaching the 3D lens filters.
Handling the 3D Lens Filters
The 3D lens filters are paired, comprising an upper lens filter and a lower
lens filter.
Handling the upper lens filter (Fig.
)
1
Loosen the screws on the left and right of the upper lens filter.
2
Lift the upper lens filter.
3
Tighten the screws that were loosened in step
1
to secure the upper
lens filter.
Handling the lower lens filter (Fig.
)
1
Loosen the screws on the left and right of the lower lens filter.
2
Lift the lower lens slightly to float the lock lever near the right side
screw.
3
Pull the lever toward you to release while supporting the lower lens
filter with one hand.
Note
When the lock lever is released, the lower lens filter may move
downward suddenly, which may cause surroundings to be damaged.
Be sure to support the filter with your hand to prevent that.
4
Move the lower lens filter down carefully.
5
Tighten the screws that were loosened in step
1
to secure the lower
lens filter.
Cleaning the 3D Lens Filters
Before cleaning
Be sure that the power is turned off and the lamp is turned off.
Cleaning the 3D lens filters
Wipe the lens gently with a soft cloth, such as a glass-cleaning cloth.
Never use solvent such as alcohol, benzene or thinner, or acid, alkaline or
abrasive detergent, or a chemical cleaning cloth, which might damage
the surface of the lens.
Note
When handling the 3D lens filters, be careful not to catch your fingers
between the lens filters.
Specifications
Dimensions (width/height (single lens filter (upper/lower)/thickness):
At no extension: Approx. 179 × 114 × 150 mm
(Approx. 7 1/8 × 4 1/2 × 6 inches)
At maximum extension: Approx. 179 × 114 ×
222 mm
(Approx. 7 1/8 × 4 1/2 × 8 3/4 inches)
Mass
Approx. 1.8 kg (Approx. 3 lb 15 oz)
Supplied accessories
Operating Instructions (1)
Filter bracket attaching screws (8)
Knob (4)
Design and specifications are subject to change without notice.
Note
Always verify that the unit is operating properly before use. SONY
WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING,
BUT NOT LIMITED TO, COMPENSATION OR REIMBURSEMENT ON
ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS DUE
TO FAILURE OF THIS UNIT, EITHER DURING THE WARRANTY PERIOD OR
AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY OTHER REASON
WHATSOEVER.
4
5
5
ᶑ㓫
㚞⛯⍱䥔濕4E擀⢘㹈₭◌
ợ䒌ḋ␥↱孛Ḹ个敩孟㚐ợ䒌存㕲᷊濇ⷚ孛⤉ⓨὁ䬅Ɂ
㣦彔
MLSB.116!4E擀⢘㹈₭◌㖓ᵲTSY.S431T㓔⪻䒙⻕㒢㖄㚞䗨4Eㇹ⻕擀⢘
丨⍬ợ䒌䗨4E㈱㎨⢻ṚɁ㙭⃚⃗Ḻ丨⍬濇孛␌孆Tpozṇ埌Ɂ
⫭堩4E擀⢘㹈₭◌
⭝ᷲ㳬岝佩
⫭堩4E擀⢘㹈₭◌䗨ⵉỀ⪼⚌㿏㿢⏰Ḟ⎼⌻Ẉ䗨⋕旍Ɂ
䒌㆛ⷸ壥㮦TpozḞ⎼⫭堩4E擀⢘㹈₭◌Ɂ
⭝ᷲTpozṇ埌
㙭⃗⫭堩4E擀⢘㹈₭◌䗨㫉樈濇孛⌦佧MLSB.116䗨㙱∅ㆯ⃰濃ᵱ斨
彥濄Ɂ
ợ䒌4E擀⢘㹈₭◌
4E擀⢘㹈₭◌㙭ᵤ⭝濇≩⎏ᵮ擀⢘㹈₭◌⏰ᵯ擀⢘㹈₭◌Ɂ
ợ䒌ᵮ擀⢘㹈₭◌濃♢
Ȏ
*
1
! 㛢ᵮ擀⢘㹈₭◌ⵊ⍗ᶈἋ䗨圞ᶁɁ
2
! ㈐峛ᵮ擀⢘㹈₭◌Ɂ
3
! ㉋䲋㫉樈
2
ᶑ㛢䗨圞ᶁ濇♞⫾ᵮ擀⢘㹈₭◌Ɂ
ợ䒌ᵯ擀⢘㹈₭◌濃♢
ȏ
*
1
! 㛢ᵯ擀⢘㹈₭◌ⵊ⍗ᶈἋ䗨圞ᶁɁ
2
! 䥱䥱㈐峛ᵯ擀⢘ợ⍗Ἃ圞ᶁ㔥䗨摥㚪䥟∌Ɂ
3
! 䒌⊹ㆯ㒓㏵ẳᵯ擀⢘㹈₭◌䗨⍰㕚濇㚁帏ặ㔝⍵㈭∌摥㚪ṉ奇
摥Ɂ
㱌び
摥㚪奇摥㕚濇ᵯ擀⢘㹈₭◌⍓偡Ṿ䧥䂚⍵ᵯ䥟∌濇⍓偡Ṿ径ㅴ⏌
♘恌Ṛ㋃⚳Ɂ∅⼩䒌ㆯ㒓㏵ẳ㹈₭◌ṉ斖㋃⚳Ɂ
4
! ⭳⼧⍵ᵯ䥟∌ᵯ擀⢘㹈₭◌Ɂ
5
! ㉋䲋㫉樈
2
ᶑ㛢䗨圞ᶁ濇♞⫾ᵯ擀⢘㹈₭◌Ɂ
㵩㱥4E擀⢘㹈₭◌
㵩㱥↱
∅⼩⃗救䒙㷴⏰ㇹ⻕㿓Ɂ
㵩㱥4E擀⢘㹈₭◌
孛ợ䒌廓ⵧ濇⣦䌟䏧㵩㱥ⵧ廟廟㑊㉑擀⢘Ɂ
⊧ᵫᵱ壥ợ䒌悶䰢ɀ剓ㅺ䥤愮↦䪭㸚↦濇ㅺ佩惜⾋ɀ䠕⾋㵩㱥↦ㅺ㑊
㱻↦ṉ⌮≺⫊㵩㱥ⵧ濇⎊ⅽ⍓偡Ṿ㋃⚳擀⢘埌曆Ɂ
㱌び
ợ䒌4E擀⢘㹈₭◌㕚濇孛⭳⼧ᵱ壥嬍ㆯ㉫⢝⚌擀⢘㹈₭◌ᶯ敘Ɂ
夨㞠
⮞⭜濃⬡0樼濃⊹ᶎ擀⢘㹈₭◌濃ᵮ0ᵯ濄濄0⋾*濕
!
ᵱ㇍⮹濕上28:!!225!!261!nn
!
㙤⢋㇍⮹濕上28:!!225!!333!nn
岌愳!!
上2/9!lh
斨Ṛ!
ợ䒌存㕲᷊濃2濄
!
㹈₭◌㒓㜚⫭堩圞ᶁ濃9濄
!
㔯搒濃5濄
嬢嬅⏰夨㞠⣦㙭⌼㙘濇⾹ᵱ⍊垰彾䝉Ɂ
㱌び
⚌ợ䒌↱孛⤯丬䟒嬈㚐㚞弴垰㫇Ɂ
㕄嬞ὁὒ㚃⃩⡺ㅺ❞ᷲṟẹ䍪䒕濇TPOZ⭝ṟẹ㋃⚳㣦ᵱ岃岇Ɂ䒕ᷲ
㚐㚞㒩昀径ㅴ䗨䌔㙭㋃⢕ㅺ柨㚃㴊㋃⢕濇ᵱỀ濃≩㉐Ẫᵱ斴ᷲ濄
彤岋ㅺ岸ΰɁ
2
1
1
Upper lens filter
上镜头滤光器
Lower lens filter
下镜头滤光器
1
1
2
3
Lock lever
锁杆
