HCD-LX7/LX8
25
25
IC101
ta
FE
WAVEFORMS
– BD (CD) SECTION –
IC101
yh
XTAI
IC101
ta
RF AC
IC101
ra
TE
IC101
wh
MDP
IC601
us
X-OUT
– PANEL FL SECTION –
IC501
qa
XC-OUT
IC501
qd
X-OUT
– MAIN (2/3) SECTION –
3.1Vp-p
16.9MHz
1.2Vp-p
(PLAY)
2.5V
APPROX 500mVp-p (PLAY)
2.5V
APPROX 200m Vp-p (PLAY)
7.5
µ
sec
2.4Vp-p
16MHz
2.8Vp-p
32.768kHz
2.8Vp-p
12.5MHz
3.6Vp-p
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed
in each block.)
For schematic diagrams.
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in
Ω
and
1
/
4
W or less unless otherwise
specified.
•
f
: internal component.
•
2
: nonflammable resistor.
•
5
: fusible resistor.
•
C
: panel designation.
For printed wiring boards.
Note:
•
X
: parts extracted from the component side.
•
a
: Through hole.
•
b
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
•
U
: B+ Line.
•
V
: B– Line.
•
H
: adjustment for repair.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
• Voltages are taken with a VOM (Input impedance 10 M
Ω
).
Voltage variations may be noted due to normal produc-
tion tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F
: FM
g
: VIDEO/MD
E
: PB (DECK A)
d
: PB (DECK B)
G
: REC (DECK B)
J
: CD
c
: digital out
I
: PHONO
• Abbreviation
EA
: Saudi Arabia model.
AR
: Argentine model.
SP
: Singapore model.
MY
: Malaysia model.
MX
: Mexican model.
AUS
: Australian model.
Note: The components identified by mark
0
or dotted line
with mark
0
are critical for safety.
Replace only with part number specified.
• Indication of transistor
Q
C
These are omitted
E
B
Caution:
Pattern face side: Parts on the pattern face side seen from the
(Side B)
pattern face are indicated.
Parts face side: Parts on the parts face side seen from the
(Side A)
parts face are indicated.
B
These are omitted.
C
E
B
These are omitted.
C
E
Содержание LBT-LX7
