Adjusting the Camera Direction and Coverage
If the MONITOR output jack is used, adjust the camera direction and coverage as
described from steps 1 to 8.
When viewing the image with the LAN cable, adjust the camera direction and
coverage as described from steps 3 to 5.
1
Fully loosen the sun shield nut until the sun shield can be slid to the front
end (when the nut is located at the back hole of sun shield slide slot),
and take off the sun shield.
2
Loosen the four front cover screws with the supplied wrench, and take
off the front cover.
3
First loosen the two base screws with the supplied wrench, then loosen
the arm screw.
To fine adjust, only loosen the arm screw.
4
Adjust the camera to turn the lens in the desired direction.
5
First tighten the two base screws with the supplied wrench, then tighten
the arm screw (tightening torque: 2.0 N·m).
6
Adjust the zoom by the ZOOM/FOCUS switch (W/T).
7
Hold down the center of the ZOOM/FOCUS switch for a moment to focus
automatically.
8
Repeat steps 3 to 7 until the coverage and the focus are determined.
Notes
When adjusting the camera direction and coverage, do not touch the front
ˎ
cover waterproof rubber gasket to prevent it from being contaminated,
detached or damaged. Otherwise, water enters the camera.
If you cannot achieve satisfactory focus by holding down the ZOOM/FOCUS
ˎ
switch due to the shooting environment, slide the ZOOM/FOCUS switch level
to N/F to focus manually.
Do not turn off this unit as soon as the focus is adjusted. Turn off after five
ˎ
minutes have passed since the focus was adjusted.
Distortion might be observed in images shot outside the specified optical
ˎ
area.
Attaching the front cover and the sun shield
1
Check if the waterproof rubber gasket is contaminated, detached or
damaged.
2
Align the four front cover screw holes with the bosses on the camera.
Make sure the TOP mark on the front cover is at the top, then tighten
the four screws with the supplied wrench to secure the front cover.
(tightening torque: 0.4 N·m)
3
Align the back hole of sun shield slide slot with the sun shield nut to
install the sun shield, adjust the sun shield to the desired position, then
tighten the sun shield nut manually.
Adjust the sun shield position as follows:
Loosen the sun shield nut manually.
Do not loosen the sun shield nut too much, to prevent it from sliding to
the back hole of sun shield slide slot.
Adjust the sun shield to the desired position horizontally.
Tighten the sun shield nut manually to secure the sun shield.
Notes
Make sure the waterproof rubber gasket is clean and fits in the groove
ˎ
properly. After installing the front cover, make sure the gap between the front
cover and the camera unit is even. Make sure there is no uneven gap or foreign
matter stuck on the gasket. Otherwise, water enters the camera. (
-4)
Poor focus may also be caused by the front cover assembly. Readjust the focus
ˎ
using the system menu.
For details, refer to the User’s Guide of the equipment.
When adjusting the factory-set position of the sun shield forward, the sun
ˎ
shield or dark vignetting may be observed in the upper sides of the images.
Also, the image quality will be reduced when the IR LED is operating.
Important precautions
Despite the fact that this unit is rated IP66, this section includes important
precautions to prevent any malfunction caused by condensation and/or water
ingress. Read the precautions below thoroughly before installing the unit.
Make sure that the cables and/or connectors of the unit that join to the
ˎ
ones of the installation surface are waterproofed, before you install the unit.
Otherwise, there may be a risk of water entering the unit through these cables.
Make sure to waterproof the cables and/or connectors with the supplied
ˎ
waterproof tape as stipulated in this manual. Otherwise, there may be a risk of
water entering and shorting the unit. For details, see “Notes on waterproofing
of cable connection areas”
in the front page.
Install the camera stand on an even ceiling, wall, etc.
ˎ
When installing the unit in an inverted position (on a ceiling, for
example)
Install the unit in a waterproof box or on a waterproof ceiling to prevent water
ˎ
entering the unit along the cables. Alternatively, seal the hole which is made
for the connecting cables at the installing surface. (
-
)
Cover all around the joint part of the installing surface and the camera stand
ˎ
with sealant to prevent water ingress. (
-
)
When installing the unit in a vertical position (on a wall, for
example)
Make sure the TOP mark on the camera stand is at the top. (
ˎ
-
)
Cover all around the joint part of the installing surface and the camera stand
ˎ
(except the water drain
-
) with sealant to prevent water ingress.
Notes on assembly
Make sure the cable and the wire rope do not get caught between the base
ˎ
stand and the mounting surface.
Before attaching the front cover to the camera unit, make sure the waterproof
ˎ
rubber gasket is clean and fits in the groove properly.
Connection
Connecting to the Network
Connect the LAN port of the camera to a router or hub in the network using a
commercially available network cable (not supplied).
Connecting the Power Source
Power supply equipment pursuant to IEEE802.3af (PoE* system)
*PoE means Power over Ethernet.
Note
Do not turn off the camera immediately after turning it on. Wait for at least five
minutes before turning off the camera.
Connecting to the power supply equipment pursuant
to IEEE802.3af
The power supply equipment pursuant to IEEE802.3af supplies the power
through a commercially available network cable. For details, refer to the
Instruction Manual of the equipment.
Specifications
Compression
Video compression format
JPEG/H.264
Audio compression format
G.711/G.726/AAC
Maximum frame rate
30 fps
Camera
IR LED
10 pcs (SNC-EB602R)/20 pcs (SNC-EB632R)
IR working distance
SNC-EB602R: 25 m (50 IRE)
SNC-EB632R: 30 m (50 IRE)
Signal system
NTSC color system/PAL color system
(switchable)
Image device
SNC-EB602R
1/3type CMOS (Exmor)
Effective picture elements:
Approx. 1,370,000
SNC-EB632R
1/2.9type CMOS (Exmor)
Effective picture elements:
Approx. 2,140,000
Synchronization
Internal synchronization
Horizontal resolution
SNC-EB602R: 600 TV lines (analog video)
SNC-EB632R: 700 TV lines (monitor display ratio
4:3)
Minimum illumination
F1.2/View-DR Off/VE* Off/Auto gain control
maximum rate MAX/50 IRE (IP)/30 fps
SNC-EB602R
Color: 0.05 lx
Black & White: 0 lx (IR ON)
SNC-EB632R
Color: 0.10 lx
Black & White: 0 lx (IR ON)
* VE stands for Visibility Enhancer.
Lens
Focal length
3.0 mm to 9.0 mm
Maximum relative aperture
F1.2 ~ F2.1
View angle
SNC-EB602R: 1280 × 1024 (aspect ratio 5:4)
Vertical: 73.1° to 25.5°
Horizontal: 92.9° to 31.8°
SNC-EB632R: 1920 × 1080 (aspect ratio 16:9)
Vertical: 56.9° to 20.1°
Horizontal: 105.3° to 35.6°
Minimum object distance
300 mm
G
1
Back hole
Sun shield nut
Sun shield
Sun shield nut
Sun shield
2
3,4,5,6,7
Base screw
Arm screw
ZOOM/
FOUCS
switch
Wrench (supplied)
For fixing the base
screws/arm screw
For fixing the
front cover screw
H
1,2
TOP mark
Rubber
gasket
Boss (four positions)
3
Sun shield nut
Sun shield
Sun shield nut
Sun shield
4
Correct
The waterproof rubber
gasket fits in the groove
properly.
After installing the front cover,
the gap between the front cover
and the camera unit is even.
Front cover
Camera unit
Wrong
I
J
Ceiling
Network cable
(straight, not
supplied)
10BASE-T/
100BASE-TX
PoE supported
device (such as a
hub)
LAN cable
K
Unit: mm (inches)
136.3 (5
3
/
8
)
85 (3
3
/
8
)
93 (3
3
/
4
)
ø140 (5
5
/
8
)
160.9 (6
3
/
8
)
188.6 (7
1
/
2
)
288.3 (11
3
/
8
)
83 (3
3
/
8
)
93 (3
3
/
4
)
Interface
LAN port (PoE)
10BASE-T/100BASE-TX, auto negotiation (RJ-45)
Others
Power supply
IEEE802.3af compliant (PoE system)
Power consumption
SNC-EB602R: 10.0 W
SNC-EB632R: 11.4 W
Operating temperature
Start temperature:
-20°C to +50°C (-4°F to +122°F)
Working temperature:
-30°C to +50°C (-22°F to +122°F)
Storage temperature
-20°C to +60°C (-4°F to +140°F)
Operating humidity
20% to 90%
Storage humidity
20% to 95%
Dimensions (diameter/height)
93 mm × 93 mm × 160.9 mm (3
3
/
4
inches ×
3
3
/
4
inches × 6
3
/
8
inches), not including the
projecting parts
Mass
Approx. 1,450 g (3 lb 3 oz)
Supplied accessories
CD-ROM (supplied programs) (1), Template (1),
Wrench (1), Installation Manual (this document)
(1 set), Safety Regulations (1 set), Waterproof
tape (1)
Design and specifications are subject to change without notice.
Recommendation of Periodic Inspections
In case using this device over an extended period of time, please have it
inspected periodically for safe use.
It may appear flawless, but the components may have deteriorated over time,
which may cause a malfunction or accident.
For details, please consult the store of purchase or an authorized Sony dealer.
Detached
Uneven gap
Uneven gap
Foreign matter stuck
