Sony ILCE-6000, Руководство по обслуживанию

Страница: 14 / 21

ILCE-6000/6000L/6000Y_L2
2-8
2-1-5. IMAGER BLOCK SECTION
ns: not supplied
Ref. No. Part No. Description Ref. No. Part No. Description
B
A
A
B
#197
#309
#309
#5
#309
#309
212
1 201
202
5 204
205
3
213
6 209
210
217
2 215
214
216
203
Mount Section
(See page 2-10)
Imager Unit Section
(See page 2-9)
4
211
(including CP6001 (CMOS imager)
and IS-095 complete board)
(Note 4)
#267
(Note 1)
208
(Note 2, 3)
207
(Note 2, 3)
206
(Note 2, 3)
ns
Note
201 4-530-608-01 FRONT FRAME (775)
202 1-880-964-11 IS-076 FLEXIBLE BOARD
203 1-880-963-11 IS-075 FLEXIBLE BOARD
204 4-474-412-01 IM HEAT SINK (2000)
205 4-487-617-01 IM RADIATION SHEET (2000)
*
206 Selection Parts IM WASHER (A), ADJUST (Note 2, 3)
*
207 Selection Parts IM WASHER (B), ADJUST (Note 2, 3)
*
208 Selection Parts IM WASHER (C), ADJUST (Note 2, 3)
209 A-1987-432-A MB CHARGE UNIT (2000)
210 1-487-619-31 SHUTTER UNIT (H094)
211 A-1987-441-A SERVICE, DEVICE UNIT (2000) (SERVICE)
(including CP6001 (CMOS imager) and IS-095 complete
board) (Note 4)
212 X-2589-179-1 CABINET FRONT ASSY (775) (BK) (BLACK)
212 X-2589-296-1 CABINET FRONT ASSY (775) (SI) (SILVER)
212 X-2590-979-1 CABINET FRONT ASSY (775) (WH) (WHITE)
213 4-530-664-01 VF RADIATION PLATE (775)
214 4-535-625-01 EM EYELET TAPE (775)
215 X-2589-183-1 STRAP BRACKET (L) ASSY (775)
216 4-487-875-01 HOLDER, EYELET TRIANGLE (779)
217 4-480-795-02 BUTTON, LENS LOCK (779) (BLACK)
217 4-480-795-11 BUTTON, LENS LOCK (779) (SILVER)
217 4-480-795-21 BUTTON, LENS LOCK (779) (WHITE)
#5 3-080-204-01 SCREW, TAPPING, P2
#197 4-185-990-01 MB SCREW, CHARGE UNIT FIXED
#267 4-287-436-21 SCREW (M1.7) (Note 1)
#309 4-300-115-21 TAPPING (1.7) (CH)
DISASSEMBLY
1. Remove in numerical order (
1
to
6
) in the left figure.
1
#309 X 2
Back View
#309
#309
2
#309 X 1
Back View
#309
3
#309 X 1
Back View
#309
4
#309 X 1
Back View
#309
5
#267 X 3
Back View
#267
6
#5 X 2
Back View
#5
Screw
#5: M1.7 X 3.5 (Tapping)
(Black)
3-080-204-01
3.5
1.7
#197: M1.6 X 4.5 (Tapping)
(Silver)
4-185-990-01
4.5
1.6
5.0
1.7
#267: M1.7 X 5.0
(Red)
4-287-436-21
#309: M1.7 X 5.0 (Tapping)
(Black)
4-300-115-21
1.7
5.0
Note 1: Refer to “Assembly-4: Screw tightening sequence when
assembling the IM Heat Sink (2000)”.
Note 1: “Assembly-4: Screw tightening sequence when assembling
the IM Heat Sink (2000)”
を参照してください。
Note 2: The IM adjust washers (A, B, C) differ in thickness. Make
sure to return the removed IM adjust washers to original
places.
When replacing IM adjust washers, refer to “2-2. SELEC-
TION PARTS” on page 2-11.
If the original state cannot be restored due to loss of the IM
adjust washer, for example, replace the Device Unit (2000)
Service.
Note 3: Refer to “Assembly-5: IM Adjust Washer (A, B, C) putting
position”.
Note 2: IM
調整ワッシャ
(A, B, C)
は，それぞれ厚さが異なります。
取り外した
IM
調整ワッシャは，必ず元の位置に戻してくだ
さい。
また，
IM
調整ワッシャを交換する際は，
2-11
ページの
“2-2.
SELECTION PARTS”
を参照してください。
IM
調整ワッシャを紛失するなどして元の状態に戻せなく
なった場合は，
Device Unit (2000) Service
を交換してくだ
さい。
Note 3: “Assembly-5: IM Adjust Washer (A, B, C) putting position”
を
参照してください。
Note 4: Precautions for Replacement of the Device Unit (2000)
Service
As CMOS Imager may be damaged by static electricity from its
structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with dusts
nor exposed to strong light.
Note 4:
Device Unit (2000) Service交換時の注意
CMOS
イメージャは構造上，静電気により破壊される恐れが
あるため，
MOS IC
と同様に注意して取り扱ってください。
また，受光部にはゴミの付着，および強い光が入ることのな
いように注意してください。
The changed portions from
Ver. 1.2 are shown in blue.
Ver. 1.3 2014.11