Chapt
er
6
Me
mor
y
Rec
o
rd
ing (Wit
h HKS
R
-102 I
n
s
ta
lled
)
76
6-2 Cache Rec
6-2 Cache Rec
The Cache Rec function captures about 100 frames of the
video and audio that the camera is currently shooting (or
about 200 frames in 50P or 59P mode) to the memory of
the HKSR-102 option board. Thus, when you press the
recording start button, the recording starts with the data
stored several seconds before (if the unit is in standby on
mode and SR Motion is not being used).
Notes
• To maximize the Cache Rec effect, it is recommend that
the Cache Rec function be used in standby on mode and
with SR Motion disabled. Though the Cache Rec
function can be used in standby off mode or together
with SR Motion, the unit may be unable to record video
and audio from immediately before you press the
recording start button.
• Cache Rec cannot be used at the same time as Timer
Rec.
The Cache Rec function is disabled by some combinations
of signal formats and target frame frequencies (see the
following table).
a
: Support Cache Rec
×: Not support Cache Rec
–: Not supported by this unit
With the formats which support SR Motion, Cache Rec
can be used together with SR Motion.
For details on the formats, see the table on page 82.
To record using the Cache Rec function
1
In the SYSTEM Setup menu, set EDIT >CACHE REC
to “100%”.
When the Cache Rec function is active, “C” appears on
the HOME screen before the number of lines of the
signal format.
2
Put this unit into standby on mode (the mode in which
the drum is rotating).
To switch from standby off mode to standby on
mode
When the unit is in stop mode, press the STOP button.
When recording is paused, press the REC button.
Note
To make the most effective use of the Cache Rec
capability, be sure to start recording with the unit in
standby on mode. The time after which the unit leaves
standby on mode and enters standby off mode can be
selected with the SERVO >STBY OFF item in the
SYSTEM Setup menu. Select a time that will be long
enough for your shooting conditions.
3
Do one of the following to start recording.
• With the REC button held down, press the PLAY
button.
Note
Be sure to press the REC button first. If you press the
PLAY button first, playback starts and the video and
audio data that has been saved to memory is cleared.
• Perform sequential recording (you will need to
record at least four seconds before pausing).
Use the procedure in
“To start sequential recording
• Record after pausing.
Record four seconds or more, and then press the
PAUSE button to pause. The unit starts to save video
and audio data to memory. Then press the PAUSE
button again to resume recording. The unit starts to
transfer data from memory to the tape.
Maximizing the Cache Rec effect
The Cache Rec function advances recording start timing
by up to five seconds. The recording start timing varies
depending on whether the SR Motion is used for recording.
The following table shows how many seconds of data are
recorded in advance of the time that the REC button is
Signal format
422
444SQ 444HQ 422×2 720_422
Target
frame frequency
23PsF
a
a
a
a
–
24PsF
a
a
a
a
–
25PsF
a
a
a
a
–
29PsF
a
a
a
a
–
50I
×
×
×
×
–
59I
×
×
×
×
–
50P
a
–
–
–
×
59P
a
–
–
–
×
ANA
EMP
1
L R
ANA
EMP
2
L R
SDI
EMP
3
L R
SDI
EMP
4
L R
SDI
EMP
5
L R
SDI
EMP
6
L R
SDI
EMP
7
L R
SDI
EMP
8
L R
SDI
EMP
9
L R
SDI
EMP
10
L R
A/E
EMP
11
L R
A/E
EMP
12
L R
dB
0
-10
-20
-30
-60
TCG
REMAIN
CH.COND
-
-
-
1080
23.98PsF
4:2:2
IN: --:--:--:--
LOCAL
EE
15:25
RECINHI
KEYINHI
00
H
00
M
00
S
00
F
PB
13.0V
SRW-1
C
Содержание HKSR-101
Страница 126: ...Index 126 Index ...
