![background image](http://html.mh-extra.com/html/sony/hcd-nx1/hcd-nx1_service-manual_420828062.webp)
9
[Aging Mode]
• Execute only if connected to the HTC-NX1.
This mode can be used for operation check of CD section and tape
deck section.
CD section and tape deck section work in parallel.
• If an error occurred:
The aging operation stops only an error occurred sections and
display then status.
• If no error occurs:
The aging operation continues repeatedly.
Procedure:
1. Set disc in DISC5 tray.
2. Load the tapes into the decks A and B respectively.
3. Press the
[PLAY MODE]
button to set the “ALL DISCS” mode,
and press the
[REPEAT]
button to “REPEAT” off.
4. Press the
[CD]
button to select the function “CD”.
5. Press three buttons of
[ENTER]
,
[POWER SAVE/DEMO]
,
and
[TUNER BAND]
simultaneously.
6. The aging mode is activated, if the indicator of disc tray num-
ber on the liquid crystal display is blinking.
7. To release from the aging mode, press the
?
/
1
button to turn
the power OFF and operate the cold reset. (Refer to the “MC
Cold Reset”)
1. Display at the Aging Mode
• Display operating state of CD section and tape deck section al-
ternately.
• If an error occurred, stop display which that section.
2. CD Section
• Display at the aging mode is the same as the normal operation.
• The sequence during the aging mode is following as below.
Aging mode sequence (CD section) :
Open the disc1 tray
Disc5 chucking
Disc5 TOC read
Disc5 play track1 for 2 seconds
Disc5 play last track for 2 seconds
• Display at an error occurred
1) Display of the error count
(1)
Press three buttons of
[ENTER]
,
[POWER SAVE/DEMO]
,
and
[GROOVE]
simultaneously.
(2)
Display of the error count following as below.
Display
EMC
**
EDC
**
Notes:
EMC
**
: The number of mechanical error.
EDC
**
: The number of no disc error after chucking the disc.
2) Display of mechanical error
Display
E
**
M##$$&&
Notes:
**
: The number of mechanical error.(“00” is latest one)
(Press the
[PLAY MODE]
button to changes next error display)
## : Not used.
$$ : Loading error. (Second figure is not used)
D : The error in the midst of close at the except mechanical trouble.
E : The error in the midst of open at the except mechanical trouble.
C : The error in the midst of chuck up at the except mechanical
trouble.
F : The error in the midst of EX-open at the except mechanical
trouble.
&&: Loading error. (Second figure in not used)
1: The error in the midst of chuck up.
2: The error in the midst of chuck down.
3: Time up of EX-open
4: Time up of EX-close.
3) Display of no disc error
Display
E
**
D##$$&&
Notes:
**
: The number of mechanical error.(“00” is latest one)
(Press the
[REPEAT]
button to changes next error display)
##:
01: Focus error
02: GFS error
03: Set up error
$$:
00: No disc error when does not chucking retry.
02: No disc error when chucking retry to completion.
&&: The state when judged no disc error. (Second figure is not used)
1: Stop
2: Set up
3: TOC read
4: Access
5: Play
6: Pause
7: Manual search (Play)
8: Manual search (Pause)
3. Tape Deck Section
Содержание HCD-NX1
Страница 58: ...5 This section is extracted from instruction manual ...
Страница 65: ...12 12 STR NX1 NX3 5 2 SCHEMATIC DIAGRAM MAIN Board 1 3 Page 13 Page 14 Page 17 Page 19 www manualscenter com ...
Страница 74: ...21 21 STR NX1 NX3 5 11 SCHEMATIC DIAGRAM PANEL Section Page 14 Page 14 www manualscenter com ...