Sony HCD-GZR333IA, Руководство по обслуживанию

Страница: 32 / 98

HCD-GZR333IA
HCD-GZR333IA
32 32
For Schematic Diagrams.
Note:
• All capacitors are in
μ
F unless otherwise noted. (p: pF) 50
WV or less are not indicated except for electrolytics and
tantalums.
• All resistors are in
Ω
and 1/4 W or less unless otherwise
speci fi ed.
• 2 : Non fl ammable resistor.
•
C
: Panel designation.
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
•
A
: B+ Line.
•
B
: B– Line.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
*
: Impossible to measure
• Voltages are taken with VOM (Input impedance 10 M
Ω
).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F
: AUDIO
f
: TUNER
L
: VIDEO
g
: COMPONENT VIDEO
E
: iPod
J
: DVD (AUDIO)
c
: DVD (RF)
I
: DVD (DIGITAL)
N
: USB
• Abbreviation
E51
: Chilean and Peruvian models
MX : Mexican model
For Printed Wiring Boards.
Note:
• X : Parts extracted from the component side.
•
Y
: Parts extracted from the conductor side.
• : Pattern from the side which enables seeing.
(The other layers’ patterns are not indicated.)
Caution:
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side) Parts on the pattern face side seen
from the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
• Abbreviation
E51
: Chilean and Peruvian models
MX : Mexican model
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(
Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
• Waveforms
– DMB19 Board –
– LCD CTRL Board –
2
IC101 ol (CVBS)
1
IC101 9 (XTALI)
3
IC101
<z/x
(SY/Y/G)
500 mV/DIV, 20 μ sec/DIV
500 mV/DIV, 20 nsec/DIV
500 mV/DIV, 20 μ sec/DIV
5
IC101 <z/v (CR/R)
4
IC101 <z/c (SC/CB/B)
6
IC101
<zxb
(RFIP)
500 mV/DIV, 20 μ sec/DIV
500 mV/DIV, 20 μ sec/DIV
200 mV/DIV, 100 nsec/DIV
1.4 Vp-p
27 MHz
0.9 Vp-p
H
0.4 Vp-p
H
0.5 Vp-p
H
0.5 Vp-p
H
700 mVp-p
– MAIN Board –
2
IC501
og
(X1)
1
IC501
os
(XT1)
0.5 V/DIV, 20 nsec/DIV
0.5 V/DIV, 20 μ sec/DIV
0.7 Vp-p
32.768 kHz
0.6 Vp-p
20 MHz
1
IC002
tf
(XOUT)
1 V/DIV, 50 nsec/DIV
1.2 Vp-p
27 MHz
Note: The components identi fi ed by mark
0
or dotted
line with mark
0
are critical for safety.
Replace only with part number speci fi ed.