![background image](http://html.mh-extra.com/html/sony/hcd-grx9000/hcd-grx9000_service-manual_420735057.webp)
– 81 –
7-33.
IC PIN FUNCTION DESCRIPTION
•
MAIN BOARD IC501
µ
PD780018AYGF-012-3BA (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Function
1
LINE-MUTE
O
Line muting on/off control signal output terminal “L”: muting on
2
DBFB-H/L
O
DBFB normal/high selection signal output to the M62442FP (IC101)
“L”: DBFB high, “H”: DBFB low
3
M62442-LATCH
O
Serial data latch pulse output to the M62442FP (IC101)
4
KEYCON-LATCH
O
Serial data latch pulse output terminal Not used (open)
5
POWER
O
Power on/off control signal output for the audio system (+5V) and deck, panel, audio system
(+7V) “L”: power on, “H”: standby
6
F-RELAY
O
Relay drive signal output for the speaker protect “H”: on
7
R-RELAY
O
Relay drive signal output for the speaker protect “H”: on Not used (open)
8
PL-RELAY
O
Relay drive signal output for the speaker protect “H”: on Not used (open)
9
VPP
—
Ground terminal
10
X2
O
Main system clock output terminal (5 MHz)
11
X1
I
Main system clock input terminal (5 MHz)
12
VDD
—
Power supply terminal (+5V)
13
XT2
O
Sub system clock output terminal (32.768 kHz)
14
XT1
I
Sub system clock input terminal (32.768 kHz)
15
RESET
I
System reset signal input from the reset signal generator (IC502) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
16
AC-CUT
I
AC off detection signal input from the reset signal generator (IC502)
17
CAPM-CNT1P
O
Capstan motor (M1) drive signal output terminal
18
SCOR
I
Subcode sync (S0+S1) detection signal input from the CXD2519Q (IC103)
19
SOFT-TEST
O
Output terminal for the software test (open)
20
NCO
O
Not used (open)
21
RDS-INT
I
Serial data reading clock signal input terminal Not used (fixed at “L”)
22
RDS-DATA
I
Serial data input terminal Not used (fixed at “L”)
23
AVDD
—
Power supply terminal (+5V) (for A/D conversion)
24
AVREF
I
Reference voltage (+5V) input terminal (for A/D conversion)
25
ADJ
I
Setting terminal for the CD test mode Normally: fixed at “H”
26
A-SHUT
I
Shut off detection signal input from the deck-A side reel pulse detector (IC1001)
27
B-SHUT
I
Shut off detection signal input from the deck-B side reel pulse detector (IC1002)
28
B-HALF
I
Detection input from the deck-B half detect switch (S1006)
29
CLK-CHECK
I
Not used (fixed at “L”)
30
SPEC-IN
I
Setting terminal for the version
31
AMS-IN
I
Automatic music sensor detection signal input from the HA12215F (IC301)
32
DEMO-CHANGE
I
Setting terminal for the demonstration H/L Fixed at “L”
33
AVSS
—
Ground terminal (for A/D conversion)
34
SQ-DATA-IN
I
Sub-code Q data input from the CXD2519Q (IC103)
35
NCO
O
Not used (open)
36
SQ-CLK
(D-OUT ON/OFF)
O
Sub-code Q data reading clock signal output to the CXD2519Q (IC103)
37
SUPERWOOFER-
ON/OFF
O
Super woofer speaker on/off control signal output terminal Not used (open)
38
SUPERWOOFER
MODE
O
Super woofer speaker mode control signal output terminal Not used (open)
39
NIL
I
Not used (fixed at “L”)
40
VSS
—
Ground terminal
41
DELAY-CONT
O
Serial data latch pulse output terminal Not used (open)
42
PL-LATCH
O
Serial data latch pulse output terminal Not used (open)
Содержание HCD-GRX9000
