27
GB
E:\Works\5003283211\5003283211DSXB700WUC\01GB-DSX-B700Wxx\030CD.fm
masterpage: Right
DSX-B700W/DSX-B700
5-003-283-
00
(1)
Troubleshooting
The following checklist will help you remedy
problems you may encounter with your unit.
Before going through the checklist below, check
the connection and operating procedures.
For details on using the fuse and removing the unit
from the dashboard, see “Connection/Installation”
(page 33).
If the problem is not solved, visit the support site on
the back cover.
General
No power is being supplied to the unit. (except
for Europe models)
If the unit is turned off and the display
disappears, the unit cannot be operated with the
remote commander.
Turn on the unit.
No sound or the sound is very low.
The position of the fader control [FADER] is not
set for a 2-speaker system.
The volume of the unit and/or connected device
is very low.
Increase the volume of the unit and connected
device.
No beep sound.
An optional power amplifier is connected and
you are not using the built-in amplifier.
The contents of the memory have been erased.
The power supply lead or battery has been
disconnected or not connected properly.
Stored stations and correct time are erased.
The fuse has blown.
Makes a noise when the position of the ignition
is switched.
The leads are not matched correctly with the car’s
accessory power connector.
During playback or reception, the demonstration
mode starts.
If no operation is performed for 5 minutes with
[DEMO-ON] set, the demonstration mode starts.
Set [DEMO-OFF] (page 20).
The display disappears from/does not appear in
the display window.
The dimmer is set to [DIMMER-ON] (page 22).
The display disappears if you press and hold OFF.
Press OFF on the unit until the display appears.
The display disappears while the unit is
operating. (Asia Pacific and India models only)
[BLACK OUT] (black out) is set to [B.OUT-ON]
(page 00).
The display/illumination flashes.
The power supply is not sufficient.
Check that the car battery supplies enough
power to the unit. (The power requirement is
12 V DC.)
The operation buttons do not function.
The connection is not correct.
Press and hold DSPL and CALL
for more than
2 seconds to reset the unit (page 8).
The contents stored in memory are erased.
For your safety, do not reset the unit while you
are driving.
The clock set automatically is not accurate.
The clock data on radio waves is not accurate.
Set the clock manually (page 00).
Radio reception
Stations cannot be received.
The sound is hampered by noises.
The connection is not correct.
If your car has built-in radio antenna (aerial) in
the rear/side glass, connect an REM OUT lead
(blue/white striped) or accessory power supply
lead (red) to the power supply lead of a car’s
antenna (aerial) booster.
Check the connection of the car antenna
(aerial).
If the auto antenna (aerial) will not extend,
check the connection of the power antenna
(aerial) control lead.
The tuning step setting has been erased.
Set the tuning step again (page 8). (Asia Pacific
and India models only)
Preset tuning is not possible.
The broadcast signal is too weak.
65 MHz to 74 MHz in FM3 cannot be tuned in.
(Europe models only)
[AREA] is set to [EUROPE].
Set [AREA] to [RUSSIA] (page 00).
RDS
RDS services cannot be received (when [AREA] is
set to [RUSSIA]). (Europe models only)
FM3 is selected.
Select FM1 or FM2.
RDS services are unavailable in the current
region.
The SEEK starts after a few seconds of listening.
(Europe models only)
The station is non-TP or has weak signal.
Deactivate TA (page 00).
010COV.book Page 27 Monday, February 4, 2019 2:03 PM
