English
WARNING
To reduce the risk of fire or electric shock, do
not expose this apparatus to rain or
moisture.
To reduce the risk of fire, do not cover the
ventilation of the apparatus with newspapers,
tablecloths, curtains, etc. And do not place lighted
candles on the apparatus.
To reduce the risk of fire or electric shock, do not
expose this apparatus to dripping or splashing,
and do not place objects filled with liquids, such
as vases, on the apparatus.
Do not install the appliance in a confined space,
such as a bookcase or built-in cabinet.
Do not expose the batteries (battery pack or
batteries installed) to excessive heat such as
sunshine, fire or the like for a long time.
As the main plug is used to disconnect the unit
from the mains, connect the unit to an easily
accessible AC outlet. Should you notice an
abnormality in the unit, disconnect the main plug
from the AC outlet immediately.
The unit is not disconnected from the AC power
source (mains) as long as it is connected to the
wall outlet, even if the unit itself has been turned
off.
The nameplate and important information
concerning safety are located on the bottom
exterior.
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate this
equipment.
CAUTION
Danger of explosion if battery is incorrectly
replaced. Replace only with the same type.
This symbol is intended to alert the user
to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute
a risk of electric shock to persons.
This symbol is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
NOTE
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one or more
of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment
and receiver.
— Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
— Consult the dealer or an experienced radio/TV
technician for help.
WARNING
Replace the battery for the clock backup with a
Sony CR2032 lithium battery, and the battery
for the remote commander with a Sony CR2025
lithium battery. Use of another battery may
present a risk of fire or explosion.
Battery may explode if mistreated. Do not
recharge, disassemble or dispose of in fire.
Dispose of used battery promptly. Keep away
from children.
Important Safety
Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9) Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade
or the third prong are provided for your safety.
If the provided plug does not fit into your
outlet, consult an electrician for replacement
of the obsolete outlet.
10) Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit
from the apparatus.
11) Only use attachments/accessories specified by
the manufacturer.
12) Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms
or when unused for long periods of time.
14) Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way, such
as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate
normally, or has been dropped.
Precautions
Play the unit on the power source specified in
“Specifications.”
Since a strong magnet is used for the speaker,
keep personal credit cards using magnetic coding
or spring-wound watches away from the unit to
prevent possible damage from the magnet.
Do not leave the unit in a location near a heat
source such as a radiator or airduct, or in a
place subject to direct sunlight, excessive dust,
mechanical vibration, or shock.
Allow adequate air circulation to prevent internal
heat build-up. Do not place the unit on a surface
(a rug, a blanket, etc.) or near materials (a
curtain) which might block the ventilation holes.
Should any solid object or liquid fall into the unit,
unplug the unit and have it checked by qualified
personnel before operating it any further.
To clean the casing, use a soft cloth dampened
with a mild detergent solution.
Never touch the wire of the external FM
antenna during a thunderstorm. Furthermore,
immediately disconnect the AC power cord
from the radio.
NOTES ON LITHIUM BATTERY
Wipe the battery with a dry cloth to assure a
good contact.
Be sure to observe the correct polarity when
installing the battery.
Do not hold the battery with metallic tweezers,
otherwise a short-circuit may occur.
If you have any questions or problems concerning
your unit, please consult your nearest Sony dealer.
Features
Clock Radio compatible with iPod/iPhone
Wake or Sleep to iPod/Radio/Buzzer
Easy to set A-B alarm
2-5-7day alarm
LCD Brightness control
MEGA BASS
MEGA Xpand
Wireless Remote Commander
No Power No Problem alarm system to keep
the clock and the alarm operating during a
power interruption with a CR2032 battery
installed
Compatible iPod/
iPhone models
Compatible iPod/iPhone models are as follows.
Update your iPod/iPhone to use the latest
software before you use it.
iPod nano
3rd generation
(video)
iPod classic
iPod
4th generation
iPod touch
1st generation
iPhone 4
iPhone
iPod nano
1st generation
iPod
4th generation
(color display)
iPhone 3G
iPod nano
4th generation
(video)
iPod touch
2nd generation
iPod nano
2nd generation
(aluminum)
iPod
5th generation
(video)
iPod mini
iPod nano
5th generation
(video camera)
iPhone 3GS
iPod touch
3rd generation
Notes
In these Operating Instructions, “iPod” is used
as a general reference to iPod functions on an
iPod or iPhone, unless otherwise specified by
the text or illustrations.
The connector of the unit is for sole use with an
iPod. If you use devices that do not match with
the connector, connect to the
AUDIO IN
jack of
this unit with the supplied audio connecting
cable.
Sony cannot accept responsibility in the event
that data recorded to an iPod is lost or damaged
when using an iPod connected to this unit.
Connecting the
antenna
To connect the AM loop
antenna
The shape and the length of the antenna is
designed to receive AM signals. Do not dismantle
or roll up the antenna.
1
Remove only the loop part from the
plastic stand.
2
Set up the AM loop antenna.
Note for customers in
Canada
The clock is preset at the factory, and its memory
is powered by the preinstalled Sony CR2032
battery. If the “AM 12:00” appears on the display
when the unit is connected to AC outlet for the
first time, the battery may be weak. In this case,
consult a Sony dealer. The preinstalled CR2032
battery is considered part of the product, and is
covered by the warranty. You are required to show
“Note for customers in Canada” (in this
instruction) to a Sony dealer in order to validate
the warranty for this product.
To know when to replace the
battery
When the battery becomes weak, “
” appears in
the display.
If a power interruption occurs while the battery is
weak, the current time and alarm will be erased.
Replace the battery with a Sony CR2032 lithium
battery. Use of another battery may cause a fire or
explosion.
To replace the battery
1
Keep the AC plug connected to the AC
outlet, remove the screw that secures the
battery compartment lid at the bottom of
the unit using a screwdriver, and open
the lid (see Fig.
).
2
Insert a new battery in the battery
compartment with the
side facing up
(see Fig.
).
3
Close the battery compartment lid and
secure it with the screw (see Fig.
).
4
Press
iPod & iPhone
,
RADIO
BAND
,
AUDIO IN
or
SNOOZE/DATE/
SLEEP
OFF
to turn “
” off in the
display.
Note
When you replace the battery, do not disconnect
the plug from the AC outlet. Otherwise, the
calendar, current time, alarm and station presets
will be erased.
Reset button
CR2032
If the time in the display is
incorrect after the battery is
changed (Reset)
Press the reset button with a pointed device. The
reset button is in the small hole located in the
battery compartment (see Fig.
).
Setting the clock for
the first time
This unit is preset to the current EST (Eastern
Standard Time) at the factory, and is powered by a
backup battery. All you need to do the first time is
just plug it in and select your time zone.
1
Plug in the unit.
The current EST (Eastern Standard Time)
appears in the display.
2
Press and hold
TIME ZONE
for at least
2 seconds.
Area number “2” flashes in the display.
3
Press
TIME SET +
or
–
repeatedly to
select the number as follows:
Area number
Time zone
1
Atlantic standard Time
2
(default setting)
Eastern standard Time
3
Central standard Time
4
Mountain standard Time
5
Pacific standard Time
6
Yukon standard Time
7
Hawaiian standard Time
4
Press
TIME ZONE
to set.
Note
Though the clock is correctly set at the factory,
discrepancies may arise during transport or
storage. If necessary, set the clock to the correct
time by referring to “Setting the clock manually.”
When Daylight Saving Time
(summer time) begins
This model automatically adjusts for Daylight
Saving Time (summer time).
“ ” is displayed from the beginning of Daylight
Saving Time (summer time) and disappears at the
end of Daylight Saving Time (summer time)
automatically.
Daylight Saving Time (summer time) begins at:
2:00 AM on the second Sunday of March.
Standard Time begins at: 2:00 AM on the first
Sunday of November.
To cancel Automatic DST/Summer Time
adjustment during the Daylight Saving
Time (summer time) period
The Automatic DST/Summer Time adjustment
can be canceled.
Press and hold
CLOCK
and
SNOOZE/DATE/
SLEEP OFF
at the same time at least 2 seconds
while the clock is displayed.
3
Insert the AM antenna terminal into the
AM ANTENNA
jack on the rear of the
unit.
To remove the AM loop
antenna
Pull the AM antenna terminal while pushing up
the terminal clamp.
Adjusting the AM loop antenna
Find a place and an orientation that provide good
reception.
Do not place the AM loop antenna near the
unit or other AV equipment, as noise may
result.
Tip
Adjust the direction of the AM loop antenna for
best AM broadcast sound.
Preparing the remote
commander
Before using the card remote commander for the
first time, remove the insulation film.
To know when to replace the
battery
With normal use, the battery (CR2025) should
last for about six months. When the remote
commander no longer operates the unit, replace
the battery with a new one.
CR2025
Notes
Do not attempt to charge the battery.
If you are not going to use the remote
commander for a long time, remove the battery
to avoid any damage that may be caused by
leakage and corrosion.
About the backup
battery
To keep accurate time, this unit contains a
CR2032 battery as a backup power source.
The battery keeps the clock and the alarm
operating in the event of a power interruption.
“ ” and “OFF” appear in the display to show that
Automatic DST/Summer Time adjustment has
been canceled. The display returns to the clock.
Notes
Changes to Automatic DST/Summer Time
adjustment by the unit (see above) are subject
to circumstances and laws in each country/
region. Should this interfere with desired
adjustment, cancel the Automatic DST/Summer
Time adjustment and set the DST display
manually as necessary. Customers living in a
country/region that does not use Daylight
Saving Time (summer time) must cancel
Automatic DST/Summer Time adjustment
before using the unit.
To activate Automatic DST/Summer Time
adjustment again, press and hold
CLOCK
and
SNOOZE/DATE/SLEEP OFF
at the same time
at least 2 seconds.
“ ” and “On” appear in the display to show that
Automatic DST/Summer Time adjustment has
been activated. The display returns to the clock.
Setting the clock manually
1
Plug in the unit.
2
Press and hold
CLOCK
until the year
flashes in the display.
3
Press
TIME SET +
or
–
repeatedly to set
the year.
4
Press
CLOCK
.
5
Repeat steps
3
and
4
to set the month,
day, hour and minute, and then press
CLOCK.
The seconds start incrementing from zero.
Notes
If you do not press any button for about
1 minute while setting the clock, the clock
setting will be canceled.
A calendar is installed in this unit. When the
date is set, the day of the week is automatically
displayed.
MON = Monday, TUE = Tuesday,
WED = Wednesday, THU = Thursday,
FRI = Friday, SAT = Saturday, SUN = Sunday
To display the year and date
Press
SNOOZE/DATE/SLEEP OFF
(
SNOOZE
on
the remote) once for the date, and press it again
for the year.
After a few seconds, the display will change back
to the current time automatically.
Setting the brightness
of the display
Three levels of brightness are available by pressing
BRIGHTNESS.
Even if you set the level of brightness to Low, it
will be changed to Middle, while alarm is
occurring.
Playing the radio
–Manual tuning
1
Press
RADIO BAND
to turn on the radio.
2
Press
RADIO BAND
repeatedly to select
the desired band.
Each press changes the band as follows:
FM1
FM2
AM
FM1 and FM2 are the same frequency bands.
3
Press
or
–
(
TUNE +
or
–
on
the remote) to tune into the desired
station.
4
Adjust volume using
or
–
(
VOL +
or
–
on the remote).
To turn off the radio, press
OFF
.
Tuning in to a station
The unit automatically scans AM or FM stations.
1
Follow steps
1
to
2
in “Manual tuning”
and select the AM or FM band.
2
Press and hold
or
–
(
TUNE +
or
–
on the remote).
+ : scans upward through the frequency bands.
– : scans downwards through the frequency
bands.
Scanning starts from the currently-tuned
frequency. When a station is received,
scanning stops.
3
Adjust the volume using
or
–
(
VOL +
or
–
on the remote).
–Preset tuning
You can preset up to 10 stations in FM (5 stations
in FM1, 5 stations in FM2), and 5 stations in AM.
Presetting a station
1
Follow steps
1
to
4
in “Manual tuning”
and manually tune into the station you
wish to preset.
2
Press and hold the desired
STATION
SELECT PRESET 1
to
5
buttons until
the preset number display changes from
flashing to fully lit.
Example:
To preset FM 89.8 MHz onto the
preset
1
button.
After a while, the display will return to the
current time.
To preset another station, repeat these steps.
To change the preset station, tune into the
desired station and hold down the
STATION
SELECT PRESET 1
to
5
button. The new
station will replace the previous station on the
preset button.
Tuning in to a preset station
1
Follow steps
1
to
2
in “Manual tuning”
and select the AM or FM band.
2
Press one of the
STATION SELECT
PRESET
buttons where the desired
station is stored.
The preset station can also be selected by
or
–
on the remote.
©2009 Sony Corporation
Printed in China
4-150-697-
23
(2)
FM/AM
Clock Radio
Operating Instructions
Mode d’emploi (au dos)
ICF-CS10iP
Dream Machine is a trademark of Sony Corporation.
Dream Machine est une marque de fabrique de Sony Corporation.
No Power No Problem is a trademark of Sony Corporation.
AC power cord
The
and VOL + buttons have a tactile dot.
PRESET
STATION SELECT
The STATION SELECT PRESET 3, and iPod & iPhone
buttons have a
tactile dot.
FM wire
antenna
Before disconnecting the iPod, pause playback.
To use the unit as a battery charger
You can use the unit as a battery charger.
Charging begins when the iPod is connected to
the unit.
Charging status appears in the display of iPod. For
details, see the user’s guide of your iPod.
On copyrights
iPhone, iPod, iPod classic, iPod nano, and iPod
touch are trademarks of Apple Inc., registered in
the U.S. and other countries.
“Made for iPod,” and “Made for iPhone” mean
that an electronic accessory has been designed to
connect specifically to iPod or iPhone,
respectively, and has been certified by the
developer to meet Apple performance standards.
Apple is not responsible for the operation of this
device or its compliance with safety and
regulatory standards. Please note that the use of
this accessory with iPod or iPhone may affect
wireless performance.
Setting the alarm
This clock radio is equipped with 3 alarm
modes—iPod, radio and buzzer. Before setting the
alarm, make sure to set the clock (see “Setting the
clock for the first time”).
To set the alarm
1
Press and hold
ALARM SET A
or
B
.
“WAKE UP” appears and the hour flashes in
the display.
2
Press
TIME SET +
or
–
repeatedly until
the desired hour appears.
To cycle the hour rapidly, press and hold
TIME
SET +
or
–
.
3
Press
ALARM SET A
or
B
.
The minute flashes.
4
Repeat step
2
to set the minute.
5
Press
ALARM SET A
or
B
.
The days of the week flash.
6
Repeat step
2
to set the days of the week.
You can select the days from the following
three options:
Every day: MON TUE WED THU FRI SAT
SUN
Week day: MON TUE WED THU FRI
Week end: SAT SUN
7
Press
ALARM SET A
or
B
.
The alarm mode setting is entered.
8
Press
TIME SET +
or
–
repeatedly until
the desired alarm mode flashes.
You can choose one of 5 settings: “iPod”,
“FM1”, “FM2”, “AM” or “BUZZER.” Set the
alarm mode as follows:
– iPod: see “
Setting the iPod alarm.”
– FM1, FM2 or AM: see “
Setting the radio
alarm.”
– BUZZER: see “
Setting the buzzer alarm.”
Setting the iPod alarm
1
Perform steps
1
to
8
in “To set the alarm.”
2
Press
ALARM SET A
or
B
to select
“iPod” alarm mode.
“VOLUME” appears in the display.
3
Press
TIME SET +
or
–
to adjust the
volume.
4
Press
ALARM SET A
or
B
.
The setting is entered.
5
If “A” or “B” does not appear in the
display, press
ALARM SET A
or
B
again.
The iPod will sound at the set time.
When using an iPod touch/iPhone
To wake up to music stored in an iPod touch/
iPhone, connect the iPod touch/iPhone to the
unit first, follow the steps above to set alarm
time, and then select the music function.
Even if the iPod alarm setting is complete, if
you turn the iPod touch/iPhone power off
before inserting the iPod touch/iPhone into the
unit, the iPod alarm will not work.
Setting the radio alarm
1
Perform steps
1
to
8
in “To set the alarm.”
2
Press
ALARM SET A
or
B
to select
radio band (“FM1”, “FM2” or “AM”).
Preset number flashes in the display.
3
Press
TIME SET +
or
–
to select the
desired preset number corresponding the
bands or “– –”.
“– –” is the last station received.
4
Press
ALARM SET A
or
B
.
“VOLUME” appears in the display.
5
Press
TIME SET +
or
–
to adjust the
volume.
6
Press
ALARM SET A
or
B
.
The setting is entered.
7
If “A” or “B” does not appear in the
display, press
ALARM SET A
or
B
again.
The radio will turn on at the set time.
Setting the buzzer alarm
1
Perform steps
1
to
8
in “To set the alarm.”
2
Press
ALARM SET A
or
B
to select
“BUZZER” alarm mode.
The setting is entered.
3
If “A” or “B” does not appear in the
display, press
ALARM SET A
or
B
again.
The buzzer will sound at the set time.
Note
The volume cannot be set for the buzzer alarm.
To confirm an alarm time setting
Press
TIME SET +
or
–
. The setting will be
displayed for about 4 seconds.
To change an alarm setting
Press and hold
TIME SET +
for at least 2 seconds
to move the alarm time forwards. Press and hold
TIME SET –
for at least 2 seconds to move the
alarm time back.
When you release the button, the changed time
will flash for about 2 seconds. To change the
alarm time again, press
TIME SET +
or
–
within
these 2 seconds, otherwise the setting change will
be fixed as displayed.
To doze for a few more minutes
Press
SNOOZE/DATE/SLEEP OFF
(
SNOOZE
on
the remote).
The sound turns off but will automatically come
on again after about 10 minutes.
You can change the snooze time by pressing
SNOOZE/DATE/SLEEP OFF
(
SNOOZE
on the
remote) repeatedly within 4 seconds.
The maximum length of the snooze time is
60 minutes.
To stop the snooze timer, press
OFF/ALARM
RESET
(
OFF
on the remote).
3
Adjust the volume using
or
–
(
VOL +
or
–
on the remote).
–Auto preset tuning
1
Follow steps
1
to
2
in “Manual tuning”
and select the AM or FM band.
2
Press and hold
RADIO BAND
until “AP”
flashes in the display.
3
Press
DISPLAY/MEMORY
.
The unit automatically presets the available
channels in order.
Tip
To stop auto preset tuning, press
OFF/ALARM
RESET
.
To display the preset number and
frequency of the current station
Press
DISPLAY/MEMORY
once for the preset
number, and press it again for the frequency.
If you press
DISPLAY/MEMORY
once only, the
display shows the preset number for about
2 seconds, then changes to the frequency.
After a few moments, the display returns to the
current time.
Improving the reception
FM:
Extend the FM wire antenna fully to increase
reception sensitivity.
AM:
Connect the supplied AM loop antenna to
the unit. Rotate the antenna horizontally for
optimum reception.
Notes on radio reception
Keep digital music players or mobile phones
away from the AM loop antenna or the FM
antenna, as this may lead to reception
interference.
When you are listening to the radio with an
iPhone connected to the unit, interference with
radio reception may occur.
When you are listening to the radio while
charging an iPod, interference with radio
reception may occur.
Tip
If the FM broadcast is noisy, press
MODE
until
“MONO” appears in the display, the radio will
play in monaural and the sound will become
clearer.
Playing an iPod
You can enjoy audio from iPod by connecting to
this unit. To use an iPod, refer to the user’s guide
of your iPod.
If you are using an iPhone, iPhone 3G, iPhone
3GS or iPhone 4, attach the supplied universal
dock adapter for iPhone, iPhone 3G, iPhone 3GS
or iPhone 4 before connecting.
The adapter number,
,
or
, is shown on
the bottom-rear of the supplied universal dock
adapters.
is for the iPhone,
is for the iPhone
3G & iPhone 3GS and
is for the iPhone 4.
Check the adapter number before use.
Universal Dock Adapter
Notes
When inserting an iPod into the unit, be sure to
use the universal dock adapter supplied with your
iPod or commercially available from Apple Inc.
The connector of the unit is exclusively for use
with an iPod. If you use a device that does not
match the connector, connect it to the
AUDIO
IN
jack of this unit with the supplied audio
connecting cable.
Sony cannot accept responsibility in the event
that data recorded on an iPod is lost or damaged
when using an iPod connected to this unit.
For details of environmental conditions for
operating your iPod, check the website of Apple
Inc.
1
Attach the adapter for your iPod/iPhone.
2
Insert your iPod/iPhone into the
connector of the unit.
3
Press
iPod & iPhone
.
The iPod begins to play automatically.
You can operate the connected iPod by this
unit or the iPod buttons.
4
Adjust the volume using
or
–
(
VOL +
or
–
on the remote).
To
Press
Turn off the iPod
OFF
, or press and
hold
iPod &
iPhone
Pause playback
iPod & iPhone
To resume play,
press it again.
Go to the next track
(forward)
Go back to the previous
track
(backward)*
Locate a point while
listening to the sound
(forward) or
(backward)
while playing and
hold it until you
find the point.
Locate a point while
observing the display
(forward) or
(backward)
in pause and hold
it until you find
the point.
Go back to the previous
menu
MENU
**
Select a menu item or a
track for playback
(up)/
(down)**
Execute the selected menu
or begin playback
ENTER
**
Change to the shuffle mode
MODE
* During playback, this operation goes back to
the beginning of the current track. To go back
to the previous track, press twice.
** These operations are available only when using
the supplied remote commander.
Notes
When placing or removing the iPod, hold the
iPod at the same angle as that of the connector
on this unit, and do not twist or bend the iPod
as connector damage may result.
Do not carry the unit with an iPod set on the
connector. Doing so may cause a malfunction.
When placing or removing the iPod, hold the
Docking Tray securely with one hand and take
care not to press the controls of the iPod by
mistake.
To stop the alarm
Press
OFF/ALARM RESET
(
OFF
on the remote)
to turn off the alarm.
The alarm will sound again at the same time the
next day.
To deactivate the alarm
Press
ALARM ON/OFF A
or
B
to turn off the
alarm A or B indicator from the display.
To activate the alarm
Press
ALARM ON/OFF A
or
B
to turn on the
alarm A or B indicator in the display.
Notes
With the alarm mode is set to iPod, when the
alarm time met, if iPod is not attached to the
unit, the alarm sound will be the buzzer.
The alarm function works as usual on the first
and last day of Daylight Saving Time (summer
time). As a result, if the Automatic DST/
Summer Time adjustment is set and the alarm
is set at a time skipped when the Daylight
Saving Time begins, the alarm is skipped; if the
alarm is set to a time that overlaps when
Daylight Saving Time ends, the alarm will
sound twice.
If the same alarm time is set for both alarm A
and B, alarm A takes priority.
If there is no operation while the alarm is
occurring, the alarm will stop after about
60 minutes.
Note on the alarm in the event of a power
interruption
In the event of a power interruption, the alarm
will work until the battery is totally discharged.
However, certain functions will be affected as
follows:
The backlight will not light up.
If the alarm mode is set to iPod or radio, it will
change to buzzer automatically.
If
OFF/ALARM RESET
is not pressed, the alarm
will sound for about 5 minutes.
If “
” appears in the display, the alarm will not
sound in the event of a power interruption.
Replace the battery if “
” appears.
The snooze function cannot be set during a
power interruption. If the snooze function has
already been set and a power interruption
occurs, the snooze function will not work.
During a power interruption, each alarm will
sound at the set time only once.
Setting the sleep timer
You can fall asleep to music, etc., using the sleep
timer. The unit stops playback or radio
automatically after a preset duration.
1
Press
SLEEP
while the unit is turned on.
“SLEEP” appears and the sleep time flashes in
the display.
2
Press
SLEEP
to set the sleep timer
duration.
Each time you press
SLEEP
, the duration (in
minutes) changes as follows:
90
60
30
15
OFF
The display returns to clock mode for about
4 seconds after you have finished the duration
setting and released
SLEEP
, and then the sleep
timer starts.
The unit plays for the duration you set, and
then stops.
To turn off the unit before the preset
time
Press
SNOOZE/DATE/SLEEP OFF
(
SNOOZE
on
the remote) or
OFF/ALARM RESET
(
OFF
on the
remote).
To change the sleep timer setting
You can press
SLEEP
repeatedly to select the
desired sleep timer setting even after the sleep
timer has been activated.
To deactivate the sleep timer
Press
SLEEP
repeatedly to set the sleep timer to
“OFF” in step
2
.
Other useful functions
To get the MEGA Xpand effect
Press
MEGA Xpand
. “MEGA Xpand” appears in
the display. You can get the effect of expansion of
the sound field. To return to normal sound, press
the button again.
To reinforce the bass sound
Press
MEGA BASS
. “MEGA BASS” appears in the
display. You can get the effect of bass of high
quality sound. To return to normal sound, press
the button again.
Connecting external
equipment
To listen to sound
1
Connect the
AUDIO IN
jack of the unit
to the line out jack or headphone jack of
the external equipment using the audio
connecting cable (supplied).
Audio connecting cable
(supplied)
To external
equipment
2
Press
AUDIO IN
to display “AUDIO IN.”
3
Play the equipment connected to the
AUDIO IN
jack.
4
Adjust the volume using
or
–
(
VOL +
or
–
on the remote).
To return to the radio
Press
RADIO BAND
.
First the preset number, then the frequency of the
last station is shown in the display.
To return to the iPod
Press
iPod & iPhone
.
To stop listening
Press
OFF/ALARM RESET
(
OFF
on the remote),
and stop playback on the connected unit.
Notes
Refer also to the connected equipment’s manual.
The supplied audio connecting cable may not
be used with some external equipment. In this
case, use a cord suitable for the external
equipment you are using.
When you listen to the radio with external
equipment connected, turn off the connected
equipment to prevent noise. If noise occurs,
even when the equipment is turned off,
disconnect and place the external equipment
away from the unit.
Troubleshooting
Should any problem persist after you have made
the following checks, consult your nearest Sony
dealer.
The clock flashes “AM 12:00” due to a power
interruption.
The battery is low. Replace the battery. Remove
the old battery and install a new one.
The radio, iPod or buzzer alarm does not
sound at the preset alarm time.
Check that alarm “A” or alarm “B” is properly
displayed.
The radio or alarm of iPod is activated but no
sound comes on at the preset alarm time.
Check the alarm volume setting.
There is no sound from the iPod.
Make sure the iPod is securely connected.
Adjust the
VOLUME
.
The iPod cannot be operated with this unit.
Make sure the iPod is securely connected.
The iPod cannot be charged.
Make sure the iPod is securely connected.
When Daylight Saving Time (summer time)
begins, the clock does not employ the
Daylight Saving Time automatically.
Make sure the clock is set correctly.
Press and hold
CLOCK
and
SNOOZE/DATE/
SLEEP OFF
simultaneously for at least
2 seconds to activate the Automatic DST
function.
Specifications
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
With 6 ohm loads both channels driven, from
150 Hz -10,000 Hz; rated 3 watts per channel
minimum RMS power, with no more than 10 %
total harmonic distortion.
Time display
12-hour system
Section for iPod
DC out: 5V
MAX: 500mA
Radio section
Frequency range
Band Frequency
Channel step
FM
87.5 MHz – 108 MHz 0.1 MHz
AM
530 kHz – 1 710 kHz 10 kHz
General
Speaker
Approx. 5.7 cm (2
1
/
4
inches) dia. 6 Ω
Input
AUDIO IN jack (ø 3.5 mm stereo minijack)
Power output
3.5 W+3.5 W (at 10% harmonic distortion)
Power requirements
120 V AC, 60 Hz
For clock back up: 3V DC, CR2032 battery (1)
Dimensions
Approx. 290.5 mm × 152.0 mm × 139.5 mm
(w/h/d)
(11
3
/
8
inches × 5
15
/
16
inches
× 5
1
/
2
inches)
including projecting parts and controls
Mass
Approx. 1.94 kg (4 lb 4 oz) including power
supply unit
Supplied accessories
Remote commander (1)
AM loop antenna (1)
Audio connecting cable (1)
Universal Dock Adapter for iPhone (1)
Universal Dock Adapter for iPhone 3G & iPhone
3GS (1)
Universal Dock Adapter for iPhone 4 (1)
Design and specifications are subject to change
without notice.
