—
4 —
CPD-100ES
4
Using Your Monitor
Preset and User Modes
The Multiscan 100
ES/200ES has factory preset modes for the 8 most
popular industry standards for true “plug and play” capability.
For less common modes, the Multiscan 100ES/200ES’s Digital
Multiscan Technology will perform all of the complex adjustments
necessary to ensure a high quality picture for any timing between
30 and 70␣ kHz.
CPD-100ES/100EST and CPD-200ES/200EST
For the customers using the Windows
®4)
95
Install the new model information of the Sony computer display
from “Windows95 Monitor Information Disk” into your PC. (To
install the file, refer to the attached “About the Windows95 Monitor
Information Disk/File”.)
This monitor complies with “VESA DDC”, the standards of
Plug&Play. If your PC/graphic board complies with DDC,
select “Plug and Play Monitor (VESA DDC)” or this
monitor’s model name (CPD-100ES/100EST or CPD-200ES/
200EST) as “Monitor type” from “Control Panel” on
Windows95. Some PC/graphic boards do not comply with
DDC. Even if they comply with DDC, they may have some
problems on connecting to this monitor. In this case, select
this monitor’s model name (CPD-100ES/100EST or CPD-
200ES/200EST) as “Monitor type” on Windows95.
Recommended horizontal timing conditions
Horizontal sync width should be: >1.0 µsec.
Horizontal blanking width should be: >3.6 µsec. (Multiscan 100
ES)/
>3.0 µsec. (Multiscan 200
ES).
Vertical sync width should be: < 560 µsec.
Note
CPD-100ES/100EST and CPD-200ES/200EST does not apply to
Macintosh 21
" color mode.
No.
1
2
3
4
5
6
7
8
Horizontal
Frequency
31.5 kHz
43.3 kHz
46.9 kHz
53.7 kHz
49.7 kHz
60.0 kHz
68.7 kHz
64.0 kHz
Resolution
(dots
×
lines)
640
×
480
640
×
480
800
×
600
800
×
600
832
×
624
1024
×
768
1024
×
768
1280
×
1024
Graphics
Mode
VGA Graphic
1)
VESA
2)
VESA
2)
VESA
2)
Macintosh
16" Color
2)
VESA
2)
VESA
2)
VESA
2)
Vertical
Frequency
60 Hz
85 Hz
75 Hz
85 Hz
75 Hz
75 Hz
85 Hz
60 Hz
Getting Started
Before using this monitor, please make sure that the following
items are included in your package: Multiscan 100
ES/200ES
monitor (1), power cord (1), warranty card (1), "Windows95
Monitor Information Disk" (1), and this operating instruction
manual (1).
This monitor will sync with any IBM or compatible system
equipped with VGA or greater graphics capability. Although
this monitor will sync to other platforms running at horizontal
frequencies between 30 and 70 kHz, including Macintosh and
Power Macintosh system, a cable adapter is required. Please
consult your dealer for advice on which adapter is suitable for
your needs.
Step 1:
With the computer switched off, attach the video
signal cable to the video output.
Step 2:
Attach the power cord to the monitor and the other
end to a power outlet.
Step 3:
Turn on the monitor and computer.
Step 4:
If necessary, adjust the user controls according to
your personal preference.
The installation of your Multiscan 100
ES/200ES is complete.
Enjoy your monitor.
1) VGA is a trademark of IBM Corporation.
2) VESA is a trademark of the non-profit organization, Video
Electronics Standard Association.
3) Macintosh is a trademark of Apple Computer Inc.
4) Windows
®
is a registered trademark of Microsoft
Corporation in the United States and other countries.
to video output
IBM or compatible
computer
Apple computer
to video output
to a power outlet
Macintosh adapter (not supplied)
Power cord (supplied)
5
COLOR
GEOM
SIZE
CENTER
RESET
Adjusting the Picture Brightness
The adjustment data becomes the common setting for all input
signals.
1
Press the
¨
>
/
.
button.
The “BRIGHTNESS/CONTRAST” OSD appears.
2
Press the
¨
>
/
.
buttons to adjust picture brightness.
.
. . . for less brightness
>
. . . for more brightness
The “BRIGHTNESS/CONTRAST” OSD disappears 3 seconds
after you release the buttons.
To reset, press the RESET button while the OSD is on.
Adjusting the Picture Centering
The adjustment data becomes the individual setting for each
input signal received.
1
Press the CENTER button.
The “CENTER” OSD appears.
2
For vertical adjustment
Press the
¨
>
/
.
buttons.
>
. . . to move up
.
. . . to move down
For horizontal adjustment
Press the
>
?
/
/
buttons.
?
. . . to move left
/
. . . to move right
To erase the “CENTER” OSD, press the CENTER button
again.
The “CENTER” OSD automatically disappears 10 seconds after
you release the buttons.
To reset, press the RESET button while the OSD is on.
∗
The horizontal and vertical frequencies for each input signal
received appear on the “BRIGHTNESS/CONTRAST” OSD.
Adjustments
When one of the preset-type signals is input, no picture
adjustment is necessary.
You can, however, adjust the picture to your preferences by
following the procedure described below.
You can adjust all items on the OSD (On Screen Display).
Control Panel
p
Before adjusting the items, turn on the unit and feed the
video signal from the connected computer/work station.
p
Adjustments will be stored automatically.
Horizontal
frequency
∗
Vertical
frequency
∗
BRIGHTNESS/CONTRAST
1 0 0
5 0
3 1 . 5 k H z / 7 0 H z
Horizontal
frequency
∗
Vertical
frequency
∗
BRIGHTNESS/CONTRAST
1 0 0
5 0
3 1 . 5 k H z / 7 0 H z
Adjusting the Picture Contrast
The adjustment data becomes the common setting for all input
signals.
1
Press the
>
?
/
/
button.
The “BRIGHTNESS/CONTRAST” OSD appears.
2
Press the
>
?
/
/
buttons to adjust picture contrast.
/
. . . for more contrast
?
. . . for less contrast
The “BRIGHTNESS/CONTRAST” OSD disappears 3 seconds
after you release the buttons.
To reset, press the RESET button while the OSD is on.
CENTER
3 2
6 8
CENTER
The operating instructions mentioned here are partial abstracts from the Operating Instruction
Manual. The page numbers of the Operating Instruction Manual remain as in the manual.
SECTION 1
GENERAL