Sony CDX-S22S, Руководство по эксплуатации

Страница: 7 / 28

7
Other functions
Changing the sound settings
Adjusting the sound
characteristics — BAL/FAD/SUB
You can adjust the balance, fader and subwoofer
volume.
1
Press
(SEL)
repeatedly until “BAL,”
“FAD” or “SUB” appears.
The item changes as follows:
LOW * 1 t MID * 1 t HI * 1 t
BAL (left-right)
t
FAD (front-rear)
t
SUB (subwoofer volume)* 2
*1 When EQ3 is activated (page 7).
*2 When the audio output is set to “SUB” (page 7).
“ATT” is displayed at the lowest setting, and can
be adjusted up to 20 steps.
2
Press the /– button
repeatedly to adjust the selected item.
After 3 seconds, the setting is complete and
the display returns to normal play/reception
mode.
With the card remote commander
In step 2, to adjust the selected item, press < , M , ,
or m .
Customizing the equalizer curve
— EQ3
“CUSTOM” of EQ3 allows you to make your
own equalizer settings.
1
Select a source, then press (EQ3)
repeatedly to select “CUSTOM.”
2
Press (SEL) repeatedly until “LOW,”
“MID” or “HI” appears.
3
Press the /– button
repeatedly to adjust the selected item.
The volume level is adjustable in 1 dB steps,
from –10 dB to +10 dB.
Repeat steps 2 and 3 to adjust the equalizer
curve.
To restore the factory-set equalizer curve,
press and hold
(SEL) before the setting is
complete.
After 3 seconds, the setting is complete and
the display returns to normal play/reception
mode.
Tip
Other equalizer types are also adjustable.
With the card remote commander
In step 3, to adjust the selected item, press < , M , ,
or m .
Adjusting setup items — SET
1
Press and hold
(SEL)
.
The setup display appears.
2
Press
(SEL)
repeatedly until the
desired item appears.
3
Press the /– button to select
the setting (example “ON” or “OFF”).
4
Press and hold
(SEL)
.
The setup is complete and the display returns
to normal play/reception mode.
Note
Displayed items will differ, depending on the source
and setting.
With the card remote commander
In step 3, to select the setting, press < or , .
The following items can be set (follow the page
reference for details):
“
z
” indicates the default settings.
*1
When the unit is turned off.
*2
When the audio output is set to “SUB.”
CLOCK-ADJ (Clock Adjust) (page 4)
BEEP
To set “BEEP-ON” (
z
) or “BEEP-OFF.”
SUB/REAR * 1
To switch the audio output.
– “SUB” (
z
): to output to a subwoofer.
– “REAR”: to output to a power amplifier.
DIM (Dimmer)
To change the brightness of the display.
– “DIM-ON”: to dim the display.
– “DIM-OFF” (
z
): to deactivate the dimmer.
DEMO * 1 (Demonstration)
To set “DEMO-ON” (
z
) or “DEMO-OFF.”
A.SCRL (Auto Scroll)
To scroll long displayed items automatically
when the group/track is changed.
– “A.SCRL-ON”: to scroll.
– “A.SCRL-OFF” (
z
): to not scroll.
LPF * 2 (Low Pass Filter)
To select the subwoofer cut-off frequency
“78HZ,” “125HZ” or “OFF” (
z
).