L
R
LINE OUT
REAR
LINE OUT
FRONT
Rear speaker
Front speaker
Power amplifier
Equipment used in illustrations (not supplied)
Connection diagram
Connection example
Right
to the interface cable of a car telephone
ATT
LINE OUT FRONT
LINE OUT REAR
REMOTE IN
to power aerial control lead or power supply lead of aerial booster
amplifier
<Note> In case of without power aerial, or aerial booster, not
necessary to connect this lead.
Notes on the control leads
• The AMP/ANT REM lead (blue/white) su12 V DC when you turn
on the unit. When the AMP/ANT REM lead is connected to the power
aerial, the aerial will be extended as long as the unit is turned on.
• A power aerial without relay box cannot be used with this unit.
Memory hold connection
When the yellow power input lead is connected, power will always be
supplied to the memory circuit even when the ignition key is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with adequate
power handling capacities. Otherwise, the speakers may be damaged.
• Do not connect the terminals of the speaker system to the car chassis,
and do not connect the terminals of the right speaker with those of the
left speaker.
• Do not attempt to connect the speakers in parallel.
• Do not connect any active speakers (with built-in amplifiers) to the
speaker terminals of the unit. Doing so may damage the active speakers.
Therefore, be sure to connect passive speakers to these terminals.
Left
Right
Left
White
Gray
Green
Purple
Yellow
Black
Red
Sky blue
Max. supply current 0.3 A
Blue/white striped
from car aerial
AMP/ANT REM
I
II
7
Fuse (10 A)
RCA pin cord (not supplied)
Notes
• Be sure to connect the earth cord before connecting the amplifier.
• If you connect an optional power amplifier and do not use the built-in amplifier, the beep sound will
be deactivated.
to a metal place in the car
First connect the black earth lead, then connect the yellow and red
power input leads.
to the +12 V power terminal which is energized at all times
Be sure to connect the black earth lead to it first.
to the +12 V power terminal which is energized at the accessory
position of the ignition key switch
Be sure to connect the black earth lead to it first.
Connections
Caution
•This unit is designed for negative earth 12 V DC operation only.
•Before making connections, disconnect the earth terminal of the car battery to avoid short circuts.
•Connect the
yellow
and
red
power input leads only after all other leads have been connected.
•Be sure to connect the red power inoput lead to the positive 12 V power terminal which is energized
when the ignition key is in the accessory position.
•
Run all earth wires to a common earth point.
•Connect the yellow cord to a free car circuit rated higher than the unit’s fuse rating. If you connect this
unit in series with other stereo components, the car circuit they are connected to must be rated higher
than the sum of the individual component’s fuse rating. If there are no car circuits rated as high as the
unit’s fuse rating, connect the unit directly to the battery. If no car circuits are available for connecting
this unit, connect the unit to a car circuit rated higher than the unit’s fuse rating in such a way that if the
unit blows its fuse, no other circuits will be cut off.
If your car has an accessory position on the ignition key switch
— POWER SELECT function
To turn the Power Select function on
Press
(OFF)
while pressing
(SOUND)
.
The Power Select function ties the clock display power to the accessory position on the ignition key
switch.
To avoid battery wear, the clock is not displayed while the unit is initializing.
Frequency select switch
The AM (FM) tuning interval is factory-set to the 9K (50k) position. If the frequency allocation system of
your country is based on 10 kHz
(200 kHz) interval, set the switch on the bottom of the unit to the 10K (200K) position before making
connections.
Reset button
When the installation and connections are complete, be sure to press the reset button with a ballpoint pen
etc.
