Sony Bravia XBR-55X900C Скачать руководство пользователя страница 188

Страница: 188 / 208

XBR-55/65X900C, 905C, 907C

188

APPENDIX-1

Software update for B board replacement

<Case1>
Panel : No Picture
SMART CORE LED : Red LED 3x blinking

B board replacement

After AC Plug-in, wait for 30sec

then turn on TV by power key
on TV or remote commander.

Check condition.

Is it the Case 1,2 or 3?

<Case2>
Panel : No Picture
SMART CORE LED : Amber & Green blinking
or Lit in White

<Case3>
Panel : Picture appear
SMART CORE LED : White Lit

Update to the latest software

version

*Remove all signal connection.

(antenna, external input, ether cable,

etc)

*Insert the USB memory.

SMART CORE LED will change to

white blinking. *

After completes,

TV will reboot by

itself and turns on

. *Disconnect the

USB memory.

Check Model name by

Service mode.

Is it the same or

different?

Same

Different

Check NVM version

affix by Service mode

to confirm the country.

Is it the same or

different?

Same

Different

Check the leftmost bit

of NVM version by

Service mode to

confirm RCD version.

Is it except 0 or 0?

“0”

Except “0”

Update to the latest software

version

*Remove all signal connection.

(antenna, external input, ether

cable, etc)

*Insert the USB memory.

SMART CORE LED will change

to white blinking. *After

completes, TV will reboot by itself

and turns on.

*Disconnect the USB memory.

Model Number setting

Serial Number input and

WB/Gamma, MURA, CUC data

transfer by Service mode

Turn off the TV by remote

power key then reboot the set

(AC OFF wait 10sec then AC

plug-in), turn on the TV by

remote power key.

Reconfirm Software version

and Model name by Service

mode

Note2:
Do not turn off TV while updating software.
If older software package version is used, software
cannot be update.
TV will reboot and turn on again.

Check the software

version by Service

mode.

Is it latest version?

Yes

Note1:
For a success of software writing,
it will take 20~30 min/time.

In case of BRA&COL, TV will enter

STDBY status. Then press "Power" key of

remote commander to turn on TV.

Содержание Bravia XBR-55X900C

















































































































































































































Результаты поиска

Содержание Bravia XBR-55X900C

Отзывы:

Похожие инструкции для Bravia XBR-55X900C

Бренды по названию

Популярные бренды

Sony Bravia XBR-55X900C, Руководство по обслуживанию

Результаты поиска

Содержание Bravia XBR-55X900C

Отзывы:

Похожие инструкции для Bravia XBR-55X900C

Бренды по названию

Популярные бренды