SONIX SN32F280 Series Скачать руководство пользователя страница 246 | Manualshive

Страница: 246 / 268

background image

SN32F280 Series

32-Bit Cortex-M0 Micro-Controller

SONiX TECHNOLOGY CO., LTD

Page 246

Version 1.1

2

2

2

1

1

1

FLASH

21.1 OVERVIEW

SONiX 32-bit MCU integrated device feature in-system programmable (ISP) FLASH memory for convenient,
upgradeable code storage. The FLASH memory may be programmed via the SONiX 32-bit MCU programming interface
or by application code for maximum flexibility. SONiX 32-bit MCU provides security options at the disposal of the
designer to prevent unauthorized access to information stored in FLASH memory.



The MCU is stalled during Flash program and erase operations, although peripherals (Timers, WDT, I/O, PWM,
etc.) remain active.



Watchdog timer should be cleared if enabled before the Flash write or erase operation.



The erase operation sets all the bits in the Flash page to logic 1.



HW will hold system clock and automatically move out data from RAM and do programming, after programming
finished, HW will release system clock and let MCU execute the next instruction.

21.2 EMBEDDED FLASH MEMORY

The Flash memory is organized as 32-bit wide memory cells that can be used for storing both code and data constants,
and is located at a specific base address in the memory map of chip.

The high-performance Flash memory module in chip has the following key features:



Memory organization: the Flash memory is organized as a User ROM, Boot ROM.

User ROM

Up to 128K Bytes divided into 128 pages of 1024 Bytes

Boot ROM

Up to 4K Bytes divided into 4 pages of 1024 Bytes

The Flash interface implements instruction access and data access based on the AHB protocol. It implements the logic
necessary to carry out Flash memory operations (Program/Erase). Program/Erase operations can be performed over
the whole product voltage range.

21.3 FEATURES



Read interface (32-bit)



Flash Program / Erase operation



Code Option includes Code Security (CS)

Write  operations  to  the  main  memory  block  and  the  code  options  are  managed  by  an  embedded  Flash  Memory
Controller  (FMC).  The  high  voltage  needed  for  Program/Erase  operations  is  internally  generated.  The  main  Flash
memory can be read/write protected against different levels of Code Security (CS).

During  a  write  operation  to  the  Flash  memory,  any  attempt  to  read  the  Flash  memory  will  stall  the  bus.  The  read
operation will proceed correctly once the write operation has completed. This means that code or data fetches cannot be
made while a write/erase operation is ongoing.

For  write  and  erase  operations  on  the  Flash  memory,  the  IHRC  will  be  turn  ON  by  FMC.  The  Flash  memory  can  be
programmed and erased using ICP and ISP.

«
...
244
245
246
247
248
...
»

Содержание SN32F280 Series













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SN32F280 Series

Бренд: BEIER-Electronic Страницы: 22

Бренд: LANGER EMV-Technik Страницы: 48

Бренд: Saftronics Страницы: 13

Бренд: ZKTeco Страницы: 14

Бренд: Unico Страницы: 164

Бренд: RADEMACHER Страницы: 68

Cutler-Hammer Jockey

Бренд: Eaton Страницы: 12

Бренд: Danfoss Страницы: 8

Бренд: Riello Страницы: 72

Бренд: ACTi Страницы: 20

Бренд: SOARNEX Страницы: 14

Бренд: Raypak Страницы: 2

Бренд: Vega Страницы: 28

Бренд: WATSON Страницы: 16

Бренд: Danfoss Страницы: 16

Бренд: ZKTeco Страницы: 27

TITAN CONTROLS KRONUS 2

Бренд: Sunlight Supply Страницы: 4

Бренд: Glitch'd Gaming Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды