SONIX SN32F280 Series Скачать руководство пользователя страница 169

Страница: 169 / 268

SN32F280 Series

32-Bit Cortex-M0 Micro-Controller

SONiX TECHNOLOGY CO., LTD

Page 169

Version 1.1

1: 8-bit RX with ACK/NACK transfer is done.

14.7.3 I2C n TX Data register (I2Cn_TXDATA) (n=0,1)

Address Offset: 0x08

This register contains the data to be transmitted.

In Master TX mode, CPU writes this register will trigger a TX function. In Slave TX mode, CPU has to write this register
before next TX procedure.

Bit

Name

Description

Attribute

Reset

31:8

Reserved

7:0

DATA[7:0]

Data to be transmitted.

R/W

0x00

14.7.4 I2C n RX Data register (I2Cn_RXDATA) (n=0,1)

Address Offset: 0x0C

Bit

Name

Description

Attribute

Reset

31:8

Reserved

7:0

DATA[7:0]

Contains the data received. Read this register when RX_DN = 1.

0x00

14.7.5 I2C n Slave Address 0 register (I2Cn_SLVADDR0) (n=0,1)

Address Offset: 0x10

Only used in slave mode. In master mode, this register has no effect.
If this register contains 0x00, the I2C will not acknowledge any address on the bus. Register ADR0 to ADR3 will be
cleared to this disabled state on reset.

Bit

Name

Description

Attribute

Reset

ADD_MODE

Slave address mode.
0 : 7-bit address mode
1: 10-bit address mode

GCEN

General call address enable bit.
0: Disable
1: Enable general call address (0x0)

29:10

Reserved

9:0

ADDR[9:0]

The I2C slave address.
ADD[9:0] is valid when ADD_MODE = 1
ADD[7:1] is valid when ADD_MODE = 0

R/W

14.7.6 I2C n Slave Address 1~3 register (I2Cn_SLVADDR1~3) (n=0,1)

Address Offset: 0x14, 0x18, 0x1C

Bit

Name

Description

Attribute

Reset

31:10

Reserved

9:0

ADDR[9:0]

The I2C slave address.
ADD[9:0] is valid when ADD_MODE = 1
ADD[7:1] is valid when ADD_MODE = 0

R/W

14.7.7 I2C n SCL High Time register (I2Cn_SCLHT) (n=0,1)

Address Offset: 0x20

Содержание SN32F280 Series













































































































































































































































































Результаты поиска

Содержание SN32F280 Series

Отзывы:

Похожие инструкции для SN32F280 Series

Бренды по названию

Популярные бренды

SONIX SN32F280 Series, Руководство пользователя

Результаты поиска

Содержание SN32F280 Series

Отзывы:

Похожие инструкции для SN32F280 Series

Бренды по названию

Популярные бренды