background image

S-36 VLF 

– USER MANUAL 

23 

4.3.4 

Safety measures 

 

Please refer also to the general safety directions given in 

section 1

. 

Only  qualified  electricians  according  to  EN  50110-1 may  operate  the  device.  It may  be  operated 

only in rooms which are safeguarded or cordoned off and marked in accordance with  EN 50191 and 
EN 50110-1.  

In  case  of  an  emergency,  a  second  operator  must  switch  off  the  device  by  actuating  the 

EMERGENCY STOP

 button or red button 

[HV off]

 and short-circuit the device. 

 

 

Never put equipment into operation in the following conditions: 

 

high humidity, 

 

condensing water vapour, 

 

moisture settling the device and measured object. 

 

In addition to an appropriate shock-hazard protection, reliable grounding of the device is required at all 
times. 

 

WARNING 

 

Make sure that the other end of the cable / cables is fenced before unintentional 
contact by unauthorized persons. 

 
Always bear in mind when carrying out capacitive tests that residual charges may still be present after 
discharging. 
 

 

WARNING 

 

Cables laid parallel to one another may also still be charged after testing! 

 
Before each test, the oil level must be visually checked (oil level in middle of oil-

level lens ± 5 mm). 

 

4.3.5 

Operating hour counter 

In each test (or at the end of the test), the operating hour counter adds the expired timer minutes 

to  the  counter  value  which  is  stored.  This  means  that  it  is  not  the  on-time  of  the  device  which  is 
determined but the real sum of test times. 

If the  interval  of  service  is  exceeded,  this  is signalled  by the  operating  hour  counter  immediately 

upon powering up of the device . 

Service interval 

 see 

sec. 5.1.2

 

4.3.6 

Data Recording (Option) 

If  the  device  is 

equipped  with  the  „Data  Recording“  feature.  The  non-volatile  built  in  memory  

of S-36 VLF is able to store about 100 records at 1 h. 

Recording of  measurement data is already described in 

sections 4.3.1

 and 

4.3.2

. 

 
To transfer data, to delete the internal data memory or setting of the internal clock, please proceed 

as follows. 

Содержание S-36 VLF





































Отзывы: