14
6. Installation
6.1
Safety precautions
WARNING
Danger of getting jammed or bruised during installation of the pump
∀
∀
WARNING
Danger of being hit by falling components
∀
∀
6.2
Installation requirements
Install the pump at a place that allows you easy access at any time. The limit values of
the ambient temperature are as foll
6.3
Installation
1.
2.
3.
Remove all covers and caps from the flanges before installing the pump.
6.3.1
Hose and pipe lines
1.
2.
3.
4.
5.
Installation
Safety precautions
WARNING
Danger of getting jammed or bruised during installation of the pump
If necessary, use lifting and holding devices suitable to the size and weight o
Make sure that all installation work is done by competent and qualified personnel only.
WARNING
Danger of being hit by falling components
If necessary, use lifting and holding devices suitable to the size and weight of the pump.
Make sure that all installation work is done by competent and qualified personnel only.
Installation requirements
Install the pump at a place that allows you easy access at any time. The limit values of
the ambient temperature are as foll
Installation
1. Install the pump in a horizontal
position. For any other installation
position, please contact the
manufacturer.
2. Note: As the pump is non
priming, it has to be supplied.
3. Make sure that the pump does not
draw in impurities when
Remove all covers and caps from the flanges before installing the pump.
Hose and pipe lines
1. All pipe line diameters should be sufficiently large. The flow rate of the suction line
should be between 1 and 2m/s, that of the discharge line
Pipe line diameters have to be at least the size of the suction and discharge ports.
2. All suction and discharge lines to the pump housing should be free of tensile stress.
3. If necessary, install expansion joints at the pipe lines to
due to the pipe’s thermal expansion.
4. Avoid bending radii of less than 1.5 times the nominal pipe size.
5. Also avoid sharp changes in diameters within the piping.
Installation
Safety precautions
Danger of getting jammed or bruised during installation of the pump
If necessary, use lifting and holding devices suitable to the size and weight o
Make sure that all installation work is done by competent and qualified personnel only.
Danger of being hit by falling components
If necessary, use lifting and holding devices suitable to the size and weight of the pump.
that all installation work is done by competent and qualified personnel only.
Installation requirements
Install the pump at a place that allows you easy access at any time. The limit values of
the ambient temperature are as foll
Installation
Install the pump in a horizontal
position. For any other installation
position, please contact the
manufacturer.
Note: As the pump is non
priming, it has to be supplied.
Make sure that the pump does not
draw in impurities when
Remove all covers and caps from the flanges before installing the pump.
Hose and pipe lines
All pipe line diameters should be sufficiently large. The flow rate of the suction line
should be between 1 and 2m/s, that of the discharge line
Pipe line diameters have to be at least the size of the suction and discharge ports.
All suction and discharge lines to the pump housing should be free of tensile stress.
If necessary, install expansion joints at the pipe lines to
due to the pipe’s thermal expansion.
Avoid bending radii of less than 1.5 times the nominal pipe size.
Also avoid sharp changes in diameters within the piping.
Safety precautions
Danger of getting jammed or bruised during installation of the pump
If necessary, use lifting and holding devices suitable to the size and weight o
Make sure that all installation work is done by competent and qualified personnel only.
Danger of being hit by falling components
If necessary, use lifting and holding devices suitable to the size and weight of the pump.
that all installation work is done by competent and qualified personnel only.
Installation requirements
Install the pump at a place that allows you easy access at any time. The limit values of
the ambient temperature are as foll
Install the pump in a horizontal
position. For any other installation
position, please contact the
Note: As the pump is non-self
priming, it has to be supplied.
Make sure that the pump does not
draw in impurities when priming.
Remove all covers and caps from the flanges before installing the pump.
Hose and pipe lines
All pipe line diameters should be sufficiently large. The flow rate of the suction line
should be between 1 and 2m/s, that of the discharge line
Pipe line diameters have to be at least the size of the suction and discharge ports.
All suction and discharge lines to the pump housing should be free of tensile stress.
If necessary, install expansion joints at the pipe lines to
due to the pipe’s thermal expansion.
Avoid bending radii of less than 1.5 times the nominal pipe size.
Also avoid sharp changes in diameters within the piping.
Danger of getting jammed or bruised during installation of the pump
If necessary, use lifting and holding devices suitable to the size and weight o
Make sure that all installation work is done by competent and qualified personnel only.
Danger of being hit by falling components
If necessary, use lifting and holding devices suitable to the size and weight of the pump.
that all installation work is done by competent and qualified personnel only.
Installation requirements
Install the pump at a place that allows you easy access at any time. The limit values of
the ambient temperature are as follows:
0 to
Install the pump in a horizontal
position. For any other installation
Make sure that the pump does not
priming.
Remove all covers and caps from the flanges before installing the pump.
All pipe line diameters should be sufficiently large. The flow rate of the suction line
should be between 1 and 2m/s, that of the discharge line
Pipe line diameters have to be at least the size of the suction and discharge ports.
All suction and discharge lines to the pump housing should be free of tensile stress.
If necessary, install expansion joints at the pipe lines to
due to the pipe’s thermal expansion.
Avoid bending radii of less than 1.5 times the nominal pipe size.
Also avoid sharp changes in diameters within the piping.
Danger of getting jammed or bruised during installation of the pump
If necessary, use lifting and holding devices suitable to the size and weight o
Make sure that all installation work is done by competent and qualified personnel only.
If necessary, use lifting and holding devices suitable to the size and weight of the pump.
that all installation work is done by competent and qualified personnel only.
Install the pump at a place that allows you easy access at any time. The limit values of
0 to +40°C for pump
Remove all covers and caps from the flanges before installing the pump.
All pipe line diameters should be sufficiently large. The flow rate of the suction line
should be between 1 and 2m/s, that of the discharge line
Pipe line diameters have to be at least the size of the suction and discharge ports.
All suction and discharge lines to the pump housing should be free of tensile stress.
If necessary, install expansion joints at the pipe lines to
Avoid bending radii of less than 1.5 times the nominal pipe size.
Also avoid sharp changes in diameters within the piping.
Danger of getting jammed or bruised during installation of the pump
If necessary, use lifting and holding devices suitable to the size and weight of the pump.
Make sure that all installation work is done by competent and qualified personnel only.
If necessary, use lifting and holding devices suitable to the size and weight of the pump.
that all installation work is done by competent and qualified personnel only.
Install the pump at a place that allows you easy access at any time. The limit values of
40°C for pumps of
Remove all covers and caps from the flanges before installing the pump.
All pipe line diameters should be sufficiently large. The flow rate of the suction line
should be between 1 and 2m/s, that of the discharge line should not exceed 3m/s.
Pipe line diameters have to be at least the size of the suction and discharge ports.
All suction and discharge lines to the pump housing should be free of tensile stress.
If necessary, install expansion joints at the pipe lines to compensate excessive tension
Avoid bending radii of less than 1.5 times the nominal pipe size.
Also avoid sharp changes in diameters within the piping.
Danger of getting jammed or bruised during installation of the pump
f the pump.
Make sure that all installation work is done by competent and qualified personnel only.
If necessary, use lifting and holding devices suitable to the size and weight of the pump.
that all installation work is done by competent and qualified personnel only.
Install the pump at a place that allows you easy access at any time. The limit values of
s of 1.4401
Remove all covers and caps from the flanges before installing the pump.
All pipe line diameters should be sufficiently large. The flow rate of the suction line
should not exceed 3m/s.
Pipe line diameters have to be at least the size of the suction and discharge ports.
All suction and discharge lines to the pump housing should be free of tensile stress.
compensate excessive tension
Install the pump at a place that allows you easy access at any time. The limit values of
All pipe line diameters should be sufficiently large. The flow rate of the suction line
should not exceed 3m/s.
Pipe line diameters have to be at least the size of the suction and discharge ports.
All suction and discharge lines to the pump housing should be free of tensile stress.
compensate excessive tension
compensate excessive tension
