Sonavision 2392 mercury Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 19

background image

Sonavision Ltd.

Aberdeen, Scotland

Issue 6

2392-31-0008

Page 16 of 19

directly into the PC COM port.  Two wire twisted pair data connection is then
made between the sonar and the data converter.

CHANGING THE COMMUNICATIONS PROTOCOL

Changing the protocol requires that the sonar unit is opened to gain access to
the  printed  circuit  boards.  This  is  carried  out  by  following  the  procedures  in
section 4.1 of this manual. This should only be attempted by an experienced
person since poor workmanship which leads to failure of the sonar unit will not
be covered by the manufacturers warranty.

The  links  which  require  changing  are  on  the  PSU  board.  This  is  the  outer
board  to  which  the  connector  on  the  housing  mates.  It  also  has  two  large
electronic modules in the centre which are easily recognizable.

The  following  diagrams  show  how  links  1  to  7  should  be  set  for  the  three
different communications protocols.

«
...
14
15
16
17
18
...
»

Содержание 2392 mercury




















Отзывы:

Нет отзывов

Похожие инструкции для 2392 mercury

Бренд: Eagle Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды