4
Before using the product for the first time, please read the instructions for use below and retain them for later reference. The original instructions were written in the Hungarian language.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety. Children should be supervised at all times to ensure that they do not play with the appliance.
After unpacking the unit, confirm that it has not been damaged during transit. Keep the packaging away from children if it contains plastic bags or other potentially hazardous components.
resettinG the unit
The microprocessor data requires resetting in situations where the power supply is lost or the unit (including its display) acts erratically. In order to do so, press the
reset
button (Figure 4) behind the front panel
using a straightened paperclip. This will clear all stored data and return the unit to factory default condition. This operation is required after installation, before switching on the unit for the first time, and when the
vehicle’s battery is replaced.
MountinG and reMoVal of the front Panel
Mounting: Holding the left side of the front panel, insert its right edge all the way into its socket so that the special tab engages and holds it securely. Then firmly press the front panel’s left side so that it snaps into
its place. Press it to the left of the CLK button.
Removal: Press the button located in the top left corner, then lift the front panel off by pulling it toward you and left.
•
Only do so when the unit has been powered off!
• Always keep the removed front panel in its protective case. Protect it from shock, dust, humidity, moisture and heat. Keep the contacts on the back of the front panel and the front of the car radio clean and avoid touching
them.
PoWerinG the unit on and off
Press the
/ Mod
button to power the unit on. It switches on (“WELCOME” is shown on display) and automatically switches to the mode listened to most recently.
• Since voltage surges can occur when the vehicle’s engine is started, only turn on the unit after the engine has been started. Turn off the unit after the engine has been stopped. To switch the unit on, press the
/ Mod
button (“GOODBYE” is shown on display).
• fter switching on, the volume and EQ settings last used before switching off will be effective.
adJustinG VoluMe
Use the
rotating knob
to set the desired volume level.
• If the unit is not in volume control mode, keep pressing the rotating knob to find the VOL mode.
• The volume can be adjusted in a range of 0 to 31. Unless an adjustment is made within 2 seconds, the unit will automatically revert to the previous function.
seleCtion of siGnal sourCe
Repeatedly press the
/ Mod
button to select the desired signal source:
TUNER / CARD (SD, SDHC, MMC) / USB / AUX
• On switching on the unit, the previously played track will continue playing unless the device containing it has been removed.
• If both the USB and SD sockets are empty, only the TUNER and AUX mode can be selected.
• If there are external devices connected to both the USB and SD sockets, the MOD button can be used to select between them. The use of SD cards is preferred due to their secure and protected location on the unit.
• After connecting, the external unit connected last will be the one that will start playing.
• Corresponding symbol illuminates after USB or SD devices are inserted. The corresponding symbol of device playing back blinks.
audio settinGs & eQ
Repeatedly and briefly press the
rotating knob
to select the parameter to be adjusted:
Vol / Bas / tre / Bal / fad / eQ / loud
Adjustment is possible by rotating the knob.
• Unless an adjustment is made within 2 seconds, the unit will automatically revert to the previous function.
• By default, the rotating knob will adjust the volume.
VoluMe
Volume adjustment (00 – 31)
Bass
Bass level adjustment (-7…0…+7)
treBle
Treble level adjustment (-7…0…+7)
BalanCe
Left and right channel balance (L7…0…R7)
fader
Front and rear channel volume fader (R7…0…F7)
eQualiZation
Pre-set EQ (EQ OFF / FLAT / CLASSIC / POP / ROCK)
loudness
Loudness control (LOUD OFF / LOUD ON)
• BALANCE L: left channel / BALANCE R: right channel / FADER R: both rear channels / FADER F: both front channels
• EQ OFF: Ordinary bass and treble adjustments are active (BASS+TREBLE)
• EQ POP / ROCK / CLASSIC: EQ settings appropriate to the music style desired
• When listening at high volume, do not set the bass and treble too high, as this may lead to distortion! The recommended setting is FLAT.
loudness
Human hearing is less sensitive to low and high frequency sound at low volumes. By turning on the
loud
function, the automatic EQ compensates for this phenomenon at lower volumes. It is recommended to be
turned off at higher volumes because it can cause the sound to be distorted.
• For the benefit of better sound quality, before using this function, we recommend selecting the setting EQ OFF and setting the bass and treble controls to “0.”
• The higher the volume, the less effect will automatic loudness correction will have on the sound.
usinG the radio
After the unit is switched on, the radio will turn on if it was being previously listened to – or the USB/SD signal source last played has been removed.
If necessary, use the
Mod
button to select the TUNER function.
Manual tuninG / storinG ProGraMs
Briefly keep pressing the
9
:
buttons to manually tune in the desired radio station. The search will stop at the next radio station. When one of the buttons is kept pressed for 2 seconds, the text
Manual
will appear,
and you can increase or decrease the tuning frequency (fine tuning). If no buttons are pressed for 2 seconds, the unit will revert to the previous
auto
search mode. If any of numerical buttons 1 to 6 are kept pressed
for 2 seconds, any station found will be stored under the preset number being pressed. The selected preset will appear in the lower left corner of the display.
• A total of 18 FM radio stations can be stored. By repeatedly pressing BND/APS button select an option from among F1-F2-F3. Six stations can be stored for each band. If for example preset 4 is selected in band F2, then band
F2 will need to be selected first (BND) and then preset button 4 pressed briefly.
• If a given preset is in use, its content will be erased and a new station frequency stored in its place.
• Whenever a station with good reception is being received, the indicator STEREO will illuminate on the display.
Figure 4
reset
Press with a sharp point if malfunctioning.
sd/sdhC/MMC
SD/SDHC/MMC memory card slot
Содержание VB 6000
Страница 59: ......
