10
EN -Functions / H - Funkciók / SK - Funkcie / RO - Funcții / SRB-MNE - Funkcije /
CZ - Funkce / HR-BIH - Funkcije
WIRELESS MICROPHONE SET
• professional metal handheld microphone • multifunction digital display in the handle • frequency / chan-
nel / battery status display • digital noise filter circuit • automatic pairing • 20 selectable channels for
interference-free reception • 6,3 mm jack microphone output on the receiver • rechargeable receiver which
can be directly plugged into the amplifier • range in open terrain: 40 m • operating frequency band: 550-
565,2 MHz • microphone: 50/33x240 mm, 2xAA (1,5 V) batteries, not included • receiver unit: 80x42x17
mm • receiver with built-in battery (500 mAh Li-Ion) • expected charging / operating time: 2,5 / 6 h • can be
charged continuously for continuous operation • accessory: USB – with microUSB charger cable (1.0 m)
INSTALLATION
Handheld microphone
The part under the display consists of a metal cylinder screwed into each other and a plastic cap. The plastic cap
does not need to be removed separately, but unscrew the metal cylinder with it. If you have carefully removed the
part of the microphone handle below the display, insert two AA (1,5 V) alkaline batteries according to the marked
polarity (positive end down). Replace the battery compartment cover. It can be switched on be pressing briefly the
button below the display, while it can be switched off the holding pressed the button (2 sec). The operating time
of alkaline batteries is typically 8…10 hours, but this may vary depending on the conditions of use. The battery
symbol on the digital display shows the status of the batteries.
Replace the batteries, if the battery symbol on the display indicates so, or the operation range decreases or the
transmission is noisy. ● The battery should be replaced by adults only. ● Do not use different kinds of batteries
and/or used and new batteries together. ● If the batteries are depleted, or you are not planning to use device for
longer period, immediately remove the batteries. ● If there is some liquid flown out, then take a protective glove
and clean the battery compartment with a dry cloth. ● Do not open, burn and short circuit the batteries. ● It is
forbidden to charge the batteries which are not rechargeable. Risk of explosion! ● Do not use accumulators
instead of batteries, because their voltage and efficiency is significantly lower! ● In cold circumstances, the power
of the batteries weakens, frequent battery replacement may needed.
Receiver
The built-in battery must be charged before the first use. Connect the supplied microUSB cable to the output of a
computer or USB charger. Set the slide switch to the OFF position. The red POWER LED lights up, and then turns
off when charging is complete. This takes approximately 2,5 hours, which provides approx. 6…7 hours of opera
-
tion. The measurement was performed at room temperature. The depleted battery is indicated by the flashing of
the POWER LED, then the receiver turns off soon. If you want to operate it continuously for a longer period of time,
you can also charge it during operation. Some chargers may make noise in the reception.
Connect the 3,6 mm mono plug to the 3,6 mm input of an amplifier, a mixer, an active sound box or a HiFi system.
Switch it on using the slide switch (ON position) and the red POWER LED lights up. If an external unit makes noise
during operation, turn the plug in the socket and set the tilt receiver to a better (usually vertical) reception position.
SETTING, PAIRING, FUNCTIONS
Turn down the volume control on the amplifier. If you have switched on both the receiver and the handheld mic
-
rophone, the green RF LED on the receiver also lights up after successful automatic pairing. Carefully set the
amplifier’s volume control into center position, while adjusting the desired volume with VOL+/- buttons on the
receiver. Then press the SET button to fix this. If the connection is not established or is not clear, switch to another
frequency. To do this, unscrew the lower part of the handle and press the SET button several times to select a
noise-free channel. You can choose from twenty channels. When changing channels, the antenna symbol flashes
briefly on the display and then lights up again after switching. Pairing is done automatically in a few seconds and
the green RF LED on the receiver is then lights continuously again. By briefly pressing the microphone’s ON/OFF
button on the microphone, the specific frequency can be read briefly instead of the channel number.
• Keep the two units to be paired close to each other. If you have a connection problem, select another frequency,
or switch the microphone and the receiver on-off, or move them elsewhere.
• The green RF LED on the receiver indicates a stable radio connection.
• Walls, nearby electrical equipment, and moving human bodies may interfere with reception and reduce the range.
Especially a mobile phone, a WiFi router, a computer or larger metal objects.
• Multiple microphone sets can be used in the same space with different channel selection.
• Too low volume may cause more noise, and too high volume may cause distorted sounding. Adjust the volume
setting of the amplifier and microphone receiver. The ideal setting depends on the placement of the microphones.
GOOD ADVICE
• The antenna of handheld microphones is located at the bottom. Therefore, do not grasp the plastic cap of the
microphones, as it may shield the transmission.
• Do not move the microphone in your hand as you may change the reception conditions.
