6.
Fix the misting board (1) to the front part of the grid (2) by tightening the lock screws (3).
7.
Screw (11)(10) together the front (2) and rear (7) part of the grid.
8.
Connect the vapour misting tube (22) to the misting board (1).
9.
Following
Figure 2.
fill up the water tank with water. Use ionized water,
which is not warmer than 40 °C. Insert the water tank to the appliance.
10.
Insert 1 pc CR2025 button cell to the remote controller.
11.
The device now can be connected to the mains outlet.
CAUTION: RISK OF ELECTRIC SHOCK!
Do not attempt to disassemble o
r
modify the unit or its accessories. In case any part is damaged,
immediately power off the unit and seek the assistance of a specialist.
In the event that the power cable should become damaged, it should only be replaced by the
manufacturer, its service facility or similarly qualified personnel.
FEATURES
humidifier fan • fan blade diameter: 40 cm • touch control • every function is remote controllable • fan speed and humidifier is adjustable in
3 stages • natural wind and night mode • oscillation (75°) • 7,5- hour fan shut down timer • humidifier switchable independently from the fan
FIGURE
1
:
1.
misting board •
2.
front part of grid •
3.
misting board lock screws •
4.
blade lock nut •
5.
fan blade •
6.
grid lock nut •
7.
back part of grid •
8.
motor shaft •
9.
motor •
10.
grid lock nut •
11.
grid lock screw •
12.
motor holder •
13.
head tilt angle adjustment •
14.
main tubular holder •
15.
tube holder fixing screw •
16.
unit body •
17.
water tank •
18.
water outlet lock screw •
19.
base •
20.
base lock nut •
21.
wheels •
22.
misting tube •
23.
control panel •
24.
remote control •
25.
decoration panel •
26.
water indicator LED
FIGURE
3
.
Control panel:
1.
natural mode indicator •
2.
sleep mode indicator •
3.
oscillation indicator •
4.
humidifying stages: low, medium, high •
5.
shut down- timer
6.
fan speed: low, medium, high •
7.
switched on status indicator
Remote control and control panel buttons:
A:
on/off switch •
B:
fan speed •
C:
fan mode •
D:
shut down-timer •
E:
oscillation switch •
F:
humidifying
FUNCTIONS OF THE DEVICE, USE
Connect the device to a standard 230 V~ / 50 Hz mains outlet! The unit will emit a short beep.
After pressing ON/OFF button once,
humidifying
function (3 stages) can be selected. If this function has selected, then the fan mode can
not be activated.
After second press ON/OFF button, the fan will start to work on the lowest stage. In fan mode additional functions can be selected such as
humidifying, timer, oscillation
and
wind
.
Fan speed stage can be selected by
SPEED
button.
With
TIMER
button, a period from 0,5 to 7,5 h can be selected which after the unit will turn off. The remaining time is the sum of the times
indicated by the LEDs.
With
MODE
button, the natural wind function can be selected, which will be indicated by a pine tree on the display, or night mode can
selected, indicated by a moon and star symbol. For normal fan mode, press the MODE button again.
The oscillating movement of the fan can be switched on or off with
OSC
button.
Press the
MIST
button to start the ultrasonic cold vaporization. The intensity can be adjusted in three stages. The power on status is
indicated by the LED indicators on the display and the blue backlight of the vertical bar on the front of the unit. If the water tank runs out of
water, it is indicated by red backlight, but the function stops
After a power cut or switch off with the remote control, all previous settings will be lost, the appliance will be in standby mode.