STEP 7- Addressing Transmitters or Specific Transmitter Channels
1) Press and hold the
PROGRAM
button on the
previously addressed transmitter
until the shade "jogs.”
2) Press and hold the
PROGRAM
button on the Additional (new) transmitter until shade "jogs."
Additional (new) transmitter is now added to shade memory and can be used to operate shade.
Assigning Specific Channels to Shade (Multi-channel transmitters only)
1) Press and hold the
PROGRAM
button on the
previously addressed transmitter
until the shade "jogs.”
2) Select the desired channel (1-4 or all) by momentarily pressing the Channel Selector Button on the
multi-channel transmitter.
3) Press and hold the
PROGRAM
button on the multi-channel transmitter until shade "jogs."
Additional (new) channel is now added to shade memory and can be used to operate shade.
Note: To Prevent unwanted Channel/Transmitter assignments, ALL PREVIOUSLY
PROGRAMMED SHADES should be UNPLUGGED until Programming is complete.
Deleting Specific Channels/Transmitters
1) Press and hold the
PROGRAM
button on the
previously addressed transmitter
until the shade "jogs.”
2) Select the desired channel (1-4 or all) or transmitter (single channel) to be deleted.
3) Press and hold the
PROGRAM
button on transmitter until shade "jogs."
Channel or transmitter is now deleted from shade memory and will not operate shade.
OPTION 1- Setting an Intermediate Shade Position (IP)
1) Press the
UP
or
DOWN
directional button on the
previously addressed transmitter
until the shade
reaches a desired intermediate position, then press the
CENTER (Stop)
button to stop. (adjust shade
position accordingly)
2) Press and hold the
CENTER
(Stop)
button on the transmitter until shade "jogs." Intermediate
position is now added to memory.
3) Activate the shade intermediate position by pressing the
CENTER
(Stop)
button from ANY shade
position.
Note:
Shade should be inactive prior to activating intermediate position function. If shade is
actively moving (in-motion)
CENTER
(Stop)
button should be pressed twice.
To Delete:
Activate shade to (IP) position, then press and hold the
CENTER (Stop)
button for 5 seconds.
OPTION 2- Re-adjusting Upper Limit (UP Stop Position)
1) Press the
UP
directional button on the transmitter. Shade will travel to the pre-set UP limit.
2) Press and hold the
UP
and
DOWN
buttons simultaneously on the transmitter until shade "jogs."
3) Press and hold either the
UP
or
DOWN
button on the transmitter to adjust shade to new position.
4) Press and hold the
CENTER (Stop)
and
UP
Button together until shade "jogs." New Upper Limit
(Up Stop position) is now added to memory.
OPTION 4- Activating Step (Tilting) Feature for Sheer shade applications
1) Press the
DOWN
directional button on the transmitter. Shade will travel to the pre-set DOWN limit.
2) Press and hold the
DOWN
button on the transmitter until shade begins to "step" or (Tilt)
3) Release the
DOWN
button on the transmitter once new position is reached.
Operating Shade with Manual Button:
Operation
- (Shade Limits MUST be set) Press manual button (located on motor housing)
momentarily, shade will begin to travel. Press manual button again to Stop.
Assigning a Transmitter
- Press and hold the manual button for (2 seconds) then immediately
press the programming button on the BACK of the Transmitter until shade "jogs.”
Clearing All Previous Programs/Limits
- Press and hold the manual button (located on motor
housing) for 12 seconds. LED will begin to blink then turn off. Motor is now cleared. Proceed to
"Step 2" and begin programming.
Adding Additional Transmitters (Single channel)
OPTION 3- Re-adjusting Lower Limit (DOWN Stop Position)
1) Press the
DOWN
directional button on the transmitter. Shade will travel to the pre-set DOWN limit.
2) Press and hold the
UP
and
DOWN
buttons simultaneously on the transmitter until shade "jogs."
3) Press and hold either the
UP
or
DOWN
button on the transmitter to adjust shade to new position.
4) Press and hold the
CENTER
(Stop)
and
DOWN
Button together until shade "jogs." New Lower Limit
(Down Stop position) is now added to memory.
Programming
Button
Somfy Systems, Inc. 7-05 Rev. 1
Channel Selector
UP
STOP
DOWN
