We reserve the right to make changes due to technical improvements.
CENTRALIS uno RTS
2
MAINS
230V - 50Hz
3 wires x 1,5 mm
2
4 wires x 0,75 mm
2
Neutral
Earth
Phase
1 2 3 4 5 6
5 wires x 1,5 mm
2
N
L
N
Centralis uno RTS
Junction box
Motor
Supply
Phase
Neutral
Earth
Earth
(green/yellow)
Common
(blue)
Up
(black or brown)
Down
(black or brown)
L
➜
N
➜
N
▲
▼
1
2
3
4
5
6
N
L
N
SUPPLY
230V 50Hz
Phase
Neutral
Earth
LT motor
DOWN
PE
N
UP
• disconnect mains before carrying out any work.
• ensure that no forces act on the screw terminals
after installation.
3
Radio programming
We reserve the right to make changes due to technical improvements.
3
CENTRALIS uno RTS
4
Operating
Wiring
2.2
Initial installation : record the first control
3.1
GROUP CONTROL (one transmitter for several receivers)
To program one control in several
CENTRALIS uno RTS
, set all the receivers in their programming mode then repeat the same procedure.
It is recommended not to use a RT control as a general control point.
To record several RTS controls in CENTRALIS uno RTS
,
repeat the same procedure as described in section 3.1 for each control.
You can also use an already recorded control to set the
CENTRALIS uno RTS
in its programming mode
RTS control :
press for more than
2 sec.
on the “prog” button.
RT control :
Contact for more than
2 sec.
between the “prog” metallic part and the battery support.
➜
The LED of the
CENTRALIS uno RTS
lights on and the blind jogs briefly UP and DOWN indicating that the
CENTRALIS uno RTS
is in programming mode and that you can record a new control.
You can program up to 12 controls to one receiver. If you try to enter a 13th, your instruction will be ignored.
P
R
O
G
Set the
CENTRALIS uno RTS
in its
programming mode by pressing the PROG
button until the blind jogs briefly (UP/DOWN).
The
CENTRALIS uno RTS
will remain
ready to record a control for two minutes.
P
R
O
G
➜
2 sec.
0
0,,5
5 s
s
➜
The blind jogs briefly (UP/DOWN)
and the LED of the
CENTRALIS
uno RTS
blinks during 5 secs.
indicating that the control has been
recorded.
CENTRALIS uno RTS
quits its
programming mode.
RTS control
Press briefly the program-
ming button on the RTS
control you wish to record.
RT control
Short contact between the
PROG metallic part and the
battery support, on the RT
control you wish to record
Record new controls
3.2
1
2
Press the prog button of the
CENTRALIS uno RTS
to enter in programming mode, then press shortly the prog button of the RTS control
you wish to remove.
It is also possible to set the
CENTRALIS uno RTS
in its programming mode with another RTS control (see 3.2), then press
shortly the prog button of the RTS control you wish to remove.
To remove all the controls, do a complete reset of the
CENTRALIS uno RTS
(see section 5).
Remove a control (on an existing installation)
3.3
CENTRALIS uno RTS
can be operated by its push-buttons or with a RT/RTS control.
“auto” position :
All commands from the push buttons of the
CENTRALIS uno RTS
(local control), from the radio controls
(master control), and sun sensor are taken into account.
“0” position :
Only the push button commands are taken into account and the radio commands are disabled (This feature
allows to isolate a room from the master control). To force the control of the
CENTRALIS uno RTS
with radio,
the radio command should be longer than 2 sec.
UP/DOWN/STOP commands
4.1
0/auto switch
4.2
Press briefly the
▼
or
▲
buttons to raise or lower the shutter/blind.
Press briefly the
■
button to stop the shutter/blind in motion.
To reach the intermediate position (section 4.4), press briefly the
■
button when the shutter/blind is at its end limits.
UP button
0/auto switch
STOP/IP button
DOWN button
Intermediate positions
4.3
With the
CENTRALIS UNO RTS
, it is possible to set one or two intermediate positions (IP) : one accessible from the top of the
shutter/blind (IP1) and one from the bottom (IP2).
To record these positions, the
CENTRALIS UNO RTS
has to record the time for the shutter/blind to go from its top to the IP and
also the time from its bottom one to the IP.
The recording of the intermediate position can be made from the
CENTRALIS uno RTS
or from a RTS control.
• Move the shutter/blind at its
UP
limit with the
▲
button and imme-
diately press the
■
button briefly.
• Press the
▼
and
■
button simulta-
neously until the shutter/blind begins
to move
DOWN
.
• Stop the shutter/blind at the inter-
mediate position you wish.
If necessary, adjust this position with
the
▲
or
▼
buttons.
• Press the
■
button more than 5 sec.
➜
The shutter/blind jogs briefly
(UP/DOWN), the 1st intermediate posi-
tion is recorded.
after
3 seconds
STOP
IP1
Set the blind to its UP limit before programming in order to always have the same adjustment.
2
1
3
4
5 sec.
UP
Programming the 1st intermediate position
(IP1)
a
0,5 s
centralis uno RTS_9007504D 30/08/06 17:17 Page 2
