CENTRALIS UNO RTS
is an individual control system for AC motor dedicated to roller shutters
and interior blind applications.
•
CENTRALIS UNO RTS
has an integrated radio receiver compatible with the RT and RTS
transmitters allowing individual, group and master commands. Up to twelve controls can be
recorded in the
CENTRALIS UNO RTS
memory.
•
The commands coming from the radio controls can be disabled thanks to the 0/auto switch.
•
One or two intermediate positions can be programmed.
•
Compatible with sensor
(sun protection functionning only)
Up to three sensors can be recorded.
inteo
CENTRALIS UNO RTS
INSTALLATION
guide
Ref.9007504D
80 mm
80 mm
33 mm 17 mm
• Main supply : 220-240V 50Hz.
• Class II product
• Protection index IP40.
• Output : 250V~ 3A
• Output temporisation : activ for 180s.
• Environmental conditions for use :
- temperature 0°C to +40°C (no condensation allowed).
- pollution degree typical for usual living space.
We reserve the right to make changes due to technical improvements.
1
CENTRALIS uno RTS
FRONT PLATE
CONTROL UNIT
FRAME
BRACKET
WALL
1
Characteristics
2
Installation
The range of radio control is limited by laws regulating
radio devices and by building design.
When planning, please ensure that there is adequate
radio reception.
In order not to affect quality of reception, a minimum
distance of 30 cm between a
CENTRALIS uno RTS
and a radio transmitter should be maintained.
CENTRALIS uno RTS
should not be installed in the
immediate vicinity of metal surfaces. Powerful local
transmitter equipment (e.g. cordless headphones) with a
transmission frequency identical to the
CENTRALIS
uno RTS
can affect its function.
Hereby, SOMFY, declares that this equipment
is in compliance with the essential require-
ments and other relevant provisions of
Directive 1999/5/EC.
A Declaration of Conformity is available at the
web address
www.somfy.com
Heading
CE
We reserve the right to make changes due to technical improvements.
CENTRALIS uno RTS
4
Nothing works:
Check the motor.
Check the power supply.
Check the battery of the transmitter.
Check that the transmitter has been properly
recorded in the CENTRALIS uno RTS’s memory.
Check for any other possible source of radio
interferences.
Phantom intermediate position:
The programmed IP can only be reached from the
UP or DOWN limits. not when the shutter is in ano-
ther position.
Lost in your programming mode:
Just make a complete reset and start again
(refer to section 5).
6
Trouble shooting guide
This device must be installed and programmed by qualified installers for whom this instruction is inten-
ded.
Before connecting the unit, read the instructions carefully.
SOMFY SAS, capital 20.000.000 Euros, RCS Bonneville 303.970.230
Assembly
2.1
Set the blind to its DOWN limit before programming in order to always have the same adjustment.
Programming the 2nd intermediate position
(IP2)
b
• Move the shutter/blind at its
DOWN
limit with the
▼
button and immedia-
tely press the
■
button briefly.
• Press the
▲
and
■
button simulta-
neously until the shutter/blind begins
to move
DOWN
.
• Stop the shutter/blind at the inter-
mediate position you wish.
If necessary, adjust this position with
the
▲
or
▼
buttons.
• Press the
■
button more than 5 sec.
➜
The shutter/blind jogs briefly
(UP/DOWN), the 2nd intermediate posi-
tion is recorded.
after
3 seconds
STOP
IP2
2
1
3
4
5 sec.
DOWN
Operating
c
• Press briefly the
■
button while the blind is
at its
UP limit
.
➜
The shutter/blind will move down and stop
at the 1st intermediate position.
1st intermediate position
IP1
UP limit
• Press briefly the
■
button while the blind is at
its
DOWN limit
.
➜
The shutter/blind will move up and stop at the
2nd intermediate position.
2nd intermediate position
IP2
DOWN limit
If you record a new IP, this will automatically erase the previous one.
If you want to erase without recording a new one, Press briefly on the
■
button to reach the IP, then:
To erase the 1st intermediate position, press
■
button for more than 5 seconds.
To erase the 2nd intermediate position, press
■
button for more than 5 seconds.
➜
The shutter/blind jogs briefly (UP/DOWN) indicating that
CENTRALIS uno RTS
has deleted the intermediate position.
Delete the intermediate position
d
5
Complete reset
To completely reset the CENTRALIS uno RTS, press its PROG button for more than 7 seconds.
This will erase all of the programmed controls, the intermediate positions.
➜
The shutter/blind jogs twice (UP/DOWN), the memory of the CENTRALIS uno RTS is cleared.
P
R
O
G
7 sec.
centralis uno RTS_9007504D 30/08/06 17:17 Page 1
