SOLZAIMA Hidro 12 Скачать руководство пользователя страница 27

Страница: 27 / 147

9.1.

Display information summary

9.1.1.

Menu

Menu indicating that the unit power is “off”, the room temperature in ºC and Time.

Selecting the operation mode

: to select the operation mode, press the “mode” key

to select “Manu” for manual mode or “Auto” for automatic mode.

“Auto” mode

: in this mode, the unit shall be turned on at maximum power until

reaching a temperature of 1ºC above the temperature selected (set point

temperature). Upon reaching the set temperature, the unit changes to minimum
operating power.

The set-point temperature can be set between 5 and 40ºC by pressing the “-” and “+”
keys.

“Manu” mode

: in this mode, the unit will run at the speed selected with the “-” key,

which may vary between 1 (minimum operating speed) and 5 (maximum operating
speed).

OFF

OF
F

OFF

MENU

OFF

MODE

OFF

ESC

OFF

MAN

AUT

OFF

20.5ºC

16:03

OFF

OFF

MENU

MODE

ESC

MAN

AUT

Mode:AUTO

enu

Temp:30

Содержание Hidro 12




















































































































































Результаты поиска

Содержание Hidro 12

Отзывы:

Похожие инструкции для Hidro 12

Бренды по названию

Популярные бренды

SOLZAIMA Hidro 12, Инструкция по эксплуатации

Результаты поиска

Содержание Hidro 12

Отзывы:

Похожие инструкции для Hidro 12

Бренды по названию

Популярные бренды