Solo SL4848-CR, Быстрый старт

Страница: 18 / 20

Ramp / Soak Control
1. Access the Initial Setup mode by pressing and holding the
;
button for three seconds. Press the
'
button repeatedly until the parameter
Ctrl
appears. Use the
,
and
.
buttons to select
pro6
for
Ramp / Soak control. Press the
;
button to save the selected value. Press the
'
button to access the
parameter
Patn
. Eight different Ramp / Soak patterns are possible with the Solo Temperature Controller. Use
the
,
and
.
buttons to select pattern number 0 through 7 for programming. Press the
;
button to save
the selected value.
2. The chart below illustrates an example of a seven step Ramp / Soak pattern (Pattern 0). Press the
'
button
to access the parameter
SP00
. Use the
,
and
.
buttons to select a setting value temperature for step
00 and press the
;
button to save the value. Press the
'
button to access the parameter
ti00
. Use the
,
and
.
buttons to enter a time in hours / minutes for step 00. Follow this procedure until the desired
number of temperature and time parameters are completed. Press the
'
button to access the parameter
psx0
. Use the
,
and
.
buttons to select the last step to be completed by the Ramp /Soak pattern. For
example, if
psx0
is set to
4
, steps 00 through 04 will be executed in the pattern.
3. Press the
'
button to access the parameter
CYC0
. Use the
,
and
.
buttons to select the number
of additional times the Ramp / Soak pattern will be executed. For example, if
CyC0
is set to
3
, the Ramp /
Soak pattern will execute a total of four times. Press the
;
button to save the selected value. Press the
'
button to access the parameter
lin0
. Use the
,
and
.
buttons to choose a Ramp / Soak pattern to
execute after the completion of Pattern 0. If set to
off
, the temperature of the last step in Pattern 0 will be held.
Press the
;
button twice to save the selected value and return to the controller main screen.
100
°
70
°
50
°
30 °
Ramp
03.00
02.00
08.00
Soak
POS0 POS1 POS2 POS3 POS4 POS5 POS6
05.00 03.00
05.00
03.00
Step00 = 50°
Time00 = 3 hrs 00 min.
Step01 = 70°
Time01 = 2 hrs 00 min.
Step02 = 70°
Time02 = 5 hrs 00 min.
SP00
ti00
SP01
ti01
SP02
ti02
Step03 = 100°
Time03 = 3 hrs 00 min.
Step04 = 100°
Time04 = 8 hrs 00 min.
Step05 = 30°
Time05 = 5 hrs 00 min.
SP03
ti03
SP04
ti04
SP05
ti05
Step06 = 30°
Time06 = 3 hrs 00 min.
Process Step = 6
Cycle times = 0
Link = OFF
SP06
ti06
psx0
CyCO
lin0
12-10
Manual Control
1. Access the Initial Setup mode by pressing and holding the
;
button for three seconds. Press the
'
button repeatedly until the parameter
Ctrl
appears. Use the
,
and
.
buttons to select
manu
for
manual control. Press the
;
button twice to save the selected value and return to the controller main screen.
2. Press the
'
button to access the parameter
out1
. Use the
,
and
.
buttons to set a value
between
)0
and
10)0
to control output #1 directly. If the controller has a discrete output, a value of
2)0
turns the output on 20% of the time. A value of
10)0
would turn the output on 100% of the time. A manually
controlled analog output value is a percentage of the analog signal. For example, if the controller has a 4-20mA
current output, a setting of
)0
would mean that the output would be 4mA. The output would be 20mA with a
setting of
10)0
. Both types of manually controlled outputs are off with a value of
00
. Press the
;
button
to save the selected value. For dual output control, press the
'
button to access the parameter
out2
. Use
the
,
and
.
buttons to set a value between
)0
and
10)0
to control output #2 directly. Press the
;
button twice to save the selected value and return to the controller main screen.
12-11