Sollae Systems CSW-M85 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 66

background image

CSW-M85 User’s Manual Ver. 1.6

Sollae Systems Co., Ltd.

- 29 -

http://www.sollae.co.kr

4

Operation Modes

4.1

What is the Operation Mode?

Each of four operation modes is defined for specific purpose as follows:



Normal mode
This mode is for normal data communication and there are 4 different connection
modes. Configuring parameters is also available in this mode.



Serial Configuration mode
This mode is for configuring environmental parameters through the serial port.



ISP mode
This mode is only for changing firmware.



Link Quality Indication mode
This mode is for indicating Wi-Fi Received Signal Strength Indication. (RSSI)

4.2

Changing modes

Figure 4-1 diagram for changing modes

①  Reset (Power off).
②  Reset or input “g 0” command.
③  Reset (After upgrading firmware, M85 will be automatically reset).
④  Reset connecting ISP# pin to GND.
⑤  Connect ISP# pin to GND for a while (over 1 sec).
⑥  Connect ISP# pin or CONFIG# pin to GND shortly (between 20ms and 1 sec).
⑦  Turn the power on.
⑧  Connect LINK_Q# pin to GND.

«
...
28
29
30
31
32
...
»

Содержание CSW-M85



































































Отзывы:

Нет отзывов

Похожие инструкции для CSW-M85

Бренд: Farris Engineering Страницы: 12

Бренд: Eastern Times Technology Страницы: 4

Бренд: Vacon Страницы: 18

Бренд: Datavideo Страницы: 8

Бренд: Faulhaber Страницы: 66

Бренд: Gardena Страницы: 14

Бренд: Gardena Страницы: 8

Бренд: ICM Controls Страницы: 2

Бренд: Zennio Страницы: 30

Бренд: Zeta Страницы: 13

Бренд: Koer Страницы: 6

Бренд: GEA Страницы: 47

XP-9 88-IoT Series

Бренд: ICP DAS USA Страницы: 8

Бренд: ICON Страницы: 2

Бренд: ICP DAS USA Страницы: 4

JetWeb JX2-PRN1

Бренд: Jetter Страницы: 25

Бренд: micro-trak Страницы: 44

Бренд: Nice Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды