EN Outdoor LED reflector lamp
Type: WM-10W-E – power: 10W
Type: WM-10WS-E – power: 10W
Type: WM-30W-E – power: 30W
Type: WM-50W-E – power: 50W
Type: WM-20W-ES – power: 20W
Type: WM-30W-ES – power: 30W
Dear customer,
Thank you for purchasing this outdoor LED lamp.
Read and follow these instructions carefully to assure that your product is used safely
and to your complete satisfaction!
Usage:
•
the lamp is designed for lighting open spaces, especially industrial areas and
around homes
•
easy to install
•
gives out a clear, intense light
•
effectively discourages unwanted visitors
Installation:
WARNING!
•
Before starting installation, during maintenance or disassembly, the power must
always be disconnected by turning off the switch or circuit breaker.
•
Work associated with connecting the lamp to the power supply should be
performed by an appropriately competent person.
•
The lamp heats up when it is on. Before performing any work with the lamp, e.g.
maintenance, the lamp must always be disconnected from the power supply and
left for a few minutes to cool down completely.
•
The lamp must not be used without the protective glass or if the protective glass is
cracked.
•
The lamp must be connected to the electrical system with a three-wire cable (with
a protective conductor), which must be fed into the lamp through the cable gland.
•
The lamp must be connected as shown in Picture 1.
L=phase=brown cable
N=
neutral = blue cable
Earth = green-yellow cable
•
It is essential to check that the wiring is connected properly before first using the
lamp.
•
Before fixing the lamp in place, check that the lamp is sufficiently far away from
nearby objects; the lit object must be at least 1m away from the protective glass –
see Picture 2.
•
Suitable for a power cable 9-12mm in diameter.
•
Finally, tighten all screws and adjust the lamp bracket to achieve the desired
lighting effect.
Troubleshooting:
If the lamp does not light up, first check the power supply.
Caution:
Keep out of reach of children; do not tamper with wiring. Technical changes are
reserved; keep this manual in a safe place.
Setting the sensor and lighting time
The knobs on the bottom of the sensor can be used to set 3 parameters of the sensor:
SENS:
Sets the sensitivity of the motion detector.
TIME:
Sets the lighting time.
LUX:
Sets the switch sensitivity in relation to ambient light conditions.
SOLIGHT Holding, s.r.o. is in no way liable for damaged caused by improper
installation of the lamp, improper electrical wiring, the use of other than the
recommended accessories, unapproved technical changes, or failure to comply with the
recommendations in this manual!
Technical specifications:
Sensor range:
max. 9m (up to 24°C)
180
o
Lighting time:
5s – 4 min
Type: WM-10W-E
Power: 10W; Voltage: 220-240V,
50/60Hz
Light source: LED COB 10W; Luminous
flux: 700lm
Chromaticity: 6000K; Material: Die-cast
aluminium
IP65
WM-10WS-E
Power: 10W; Voltage: 220-240V,
50/60Hz
Light source: LED COB 10W; Luminous
flux: 700lm
Chromaticity: 6000K; Material: Die-cast
aluminium
IP44
Type: WM-30W-E
Power: 30W; Voltage: 220-240V,
50/60Hz
Light source: LED COB 30W; Luminous
flux: 2100lm
Chromaticity: 6000K; Material: Die-cast
aluminium
IP65
Type: WM-50W-E
Power: 50W; Voltage: 220-240V,
50/60Hz
Light source: LED COB 50W; Luminous
flux: 3500lm
Chromaticity: 6000K; Material: Die-cast
aluminium
IP65
WM-20W-ES
Power:
20W; Voltage: 220-240V,
50/60Hz
Light source: LED COB 20W; Luminous
flux: 1400lm
Chromaticity: 6000K; Material: Die-cast
aluminium
IP44
WM-30W-ES
Power:
30W; Voltage: 220-240V,
50/60Hz
Light source: LED COB 30W; Luminous
flux: 2100lm
Chromaticity: 6000K; Material: Die-cast
aluminium
IP44
Picture 1
Picture 2
